Hi folks,
I'm having some UART trouble - help would be much appreciated, and thank you in advance.
------------------------
Overview:
I'm working on a project that...
Hi everybody I'm using nRF Connect SDK 2.6.1. I have my own board based on nRF52840 SoC. I made an overlay file of nRF52840DK and changed its UART TX/RX settings according...
Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
In the past few months I got aware, that some, in my opinion simple questions, get marked with
"This comment is under review"
and then nothing happens. For weeks, even...
running Windows 10 Pro 22H2 and using j-link v9
i tried to read firmware from nrf51822-QFAB by using " nrfjprog --readcode dump_nRF51822.hex", but it gave me an error...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Hi,
Since migrating to SES 4.18 erasing of the flash hangs unless the JLink is unplugged and plugged in again. This is both on the DK and our own custom board. Here's the...
I looked at the info center for the part as well as the 3rd party modules; but couldn't find an FCC ID.
Does this chip (or possibly an equivalent part) have an FCC ID?
Hey All,
I'm building firmware for a central, that I want to have the ability to switch between scanning for a complete local name, or if none is given, scanning by way...
I'm working on adding support for a custom NRF9160-based board to the ncs project. It appears to be working by simply duplicating the DK and making some modifications, however...
Hi,
I merge saadc and ble_uart together in order to send send sensor output(now just analog voltage) to mobile app. I want to check weather the ADC is working properly or...
Greetings to all,
I'm using nRF52840 with the latests SDKs (nRF5 SDK 15.3.0, mesh SDK 3.2.0). I have two questions which are related-
I'm trying to find a clever way...
I thought this should be very simple but it has not turned out that way. I have started with the pc-ble-driver heart rate monitor (peripheral) example. I was able to take...
Hi,
I am looking for (andriod) mobile phone that support Bluetooth LE coded (long range)
Have you ever tested bluetooth (LE coded) with mobile phone ?
Please recommend...
I am currently developing firmware that needs to run on both 32 and 40 chips.
The basics of the situation is the firmware contains 3 'applications'. A flag in the UICR region...
Hello,
I have been looking through the SDK for the Thingy:52, and I have been unable to find the configuration file used for the MPU-9250. I am able to see the default pedometer...
I use QSPI to access MT25qu512 serial flash and find the following behavior.
SDK: nRF5_SDK_15.3.0_59ac345
QSPI configuration:
// Use 4 bytes address from serial flash...
I am unable to figure out what causes the problem that IRQ handler is defined both in nrfx_uart and nrfx_uarte modules.
After investigating in a test project I have found...
I have previously built the Asset Tracker downloaded it to my 9160DK with no problems.
Today I connected my Thingy91 and updated it's firmware. Afterwards I built the Asset...
