Good morning,
In my application (SDK v 2.8.0) I would like to disable/enable runtime the advertising for the mesh provisioning. The inizialization of the mesh stack works...
Hi,
Our project need 7 seperate PWM outputs, as the nRF52840 have 4 hardware pwm, I decide to use GPIOTE with PPI to create extra 3 pwm outputs to drive Red/Green/Blue...
Hi, last year the name of the Zephyr module "TraceRecorderSource" was changed to "percepio". In January a PR was accepted that updated the SDK's allow-list (west.yml).
We...
Four returned products after sale could not be turned on & charged normally. Preliminary analysis of disassembly showed that the MCU was damaged, and the MCU was cross-verified...
hi support team,
may i ask do we have demo on how to test remote provision in ncs2.9.0?
i assume there are two possiblilities:
1.
For server, we need add below settings...
Hello,
We are using a BLE module based on nRF52832 with a U.FL connector for external antenna connection. One of our automated tests requires we turn off/on the antenna...
Hi,
I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
HI,
I am using nrf52832 with sdk15.2.0 and softdevice s132. I face some issue related MAC address of nrf52832.
when I reset the sensor MAC address of the sensor change...
I am trying to step through the code of an example of the nRF5_SDK_16.0.0 on the nRF52 DK board.
I downloaded the latest version of Segger Embedded Studio (v4.30c) and I...
Hello,
I have a brand new Thingy 91 running the default asset tracker application connected to nrfCloud.
I wanted to build the asset_tracker myself and upload it to validate...
Hello, I just got an nrf9160dk with hopes that it would allow me to reprogram a Thingy91 that I couldn't program through the MCU method. (this is an still open ticket: https...
I use nrf5_SDK_for_Mesh_v3.2.0_src\examples\experimental_lpn and board PCA10040.
When I close main.c ERROR_CHECK(sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE)), nRF Mesh...
Hello,
I'm started implementing DFU over serial port and see documentation from this link: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5...
Hi, I am now using nRF24lu1p, for using cklf_wdog_init() to enable watchdog, then I set cklf_wdog_init(10) in main function, but don't know how to set watchdog event handle...
So we have been developing on the nRF52811 and realized we need OTA (Over the air Frimware) aswell and we have 30kB Flash and 8kB Ram remaining. Can this be done?
Also a...
Dear Sir/Madam,
I am trying following,
1. Avoiding SPIM transfer interrupt handler.
I am performing following steps,
1. nrf_drv_spi_init() for Handler parmater 'NULL...
Hello,
I'm using nRF connect for power profiling of nRF52840 DK. First time it works.
If we close the nRF connect and open it again then I get error.(Also after power...
How can I do LESC on my central with an Android peripheral device, if with each new connection the MAC address on Andriod changed randomly?
The first time I am making a...
Hello,
I want to use 100 bytes of flash as non-volatile data memory. We should be able to read and write this memory during execution.
So for this purpose I need the implementation...
I already follow the link for terminal in this link https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v16.0.0%2Flib_cli.html&cp=6_1_3_10_3&anchor=lib_cli_terminal_settings...
nRF52DK
p20 debug out
external board is 51822 + sensors
I managed to connect the external board through p20 on the 52DK. I can successfully program the external board...
