I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I have PCA63511 Power Profiling DK and nRF52840 DK ( and nRF9160-DK )
I was using SoftDevice SDK, and no issues with measuring nRF52840 device. But now I switched...
As state in the title I am trying to run pc-ble-driver on nRF52840 Dongle running examples on Mac OSX.
I uploaded connectivity_4.1.4_usb_with_s140_6.1.1.hex file on my dongle...
Dear:
Do you have any cases about wireless serial port printing debugging at nRF52832 BLE device ？
When the device is not connected to the debugging line, the dongle can...
Hello everyone,
Im developing a simple BLE scanner and its purpose is to receive and send beacons data by serial port.
My application worked quite well when flashing to...
Hello,
I have been trying to debug a curious behavior leading to higher energy consumption (~17mA) on my Sleepy End Device (Rx is off when idle).
I am using the nRF SDK...
Hi There,
If I want to put some files, like video on the nRF52840 boards, and let them broadcast onto other devices. How can I do to find the flash path of the video file...
I'm having a hard time getting nrfjprog to remain in my PATH env variable when using the Toolchain manager. I am following this post -- I am able to `echo` my PATH variable...
Hi
I am usig a nRF52840 with the chip antenna 2450AT18D0100E (Johanson Technology).
How should I calculate the matching filter? I used the values from the reference design...
Hi all,
We met a problem with uart while producting our device. It happened when we communicating with our NB module(BC28), then i catch the waveform by the oscilloscope...
Hi, I'm trying to migrate to Nordic nRF Connect APIs for Direction Finding. To start I just tried getting the samples direction_finding_connectionless_rx and direction_finding_connectionless_tx...
Hi team,
Our customer asked about how to create their own mcuboot repository and module on ncs1.6.1. They hope this module can be added into the Zephyr build system, and...
Hello,
I am using nRF9160DK(PCA10090, 1.0.0)
I am using UDP sample to check power consumption and estimation.
PPK2 is used for this test. It looks OK.
I also like...
The documentation for setting up the characteristics is very thin - its no better than what one can read in the h-files. This method
sd_ble_gatts_characteristic_add (uint16_t...
