Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
Hi,
I am trying to send messages from my gateway, which has UART and __LOG enabled, to a specific LPN address (0003).
So I want to send messages from my FN Light1 (0002...
We have developed an application in ncs-1.3.0 where we created a west.yml file for the application that lists nrf, zephyr and other dependent repositories. We have downstream...
Hello. everybody.
I'm new to be here.
Now, I'm struggling to succeed in building 'ble_app_beacon_pca10040_s132.uvprojx'.
(This file located in C:\(private dir)\nRF5_SDK_12...
We encounter 52810 freezing problem. It occurses in low probability less than 1 out of 1000.
Power-on reset is no use for this problem. The freezed 52810 chip restored when...
Hello,
I am developing a product that acts as a peripheral and sends a notification of more than 20 bytes (which is by default the BLE MTU). How can I config the MTU so...
Hallo I'm writing Data to the I2C port.
I'm using the nrf_drv_twi_tx function. It works well.
But I want to write bytes to the I2C without Adress. - i want to write just...
Hi,
I have the nrf5340 development kit. This is my first time working on Nordic devices. I've followed the Getting Started Guides. I am trying to run the first test. My...
Hi,
I'm trying to m ake sure that the nRF Sniffer files can be run correctly, following the instructions: "On Windows, type nrf_sniffer_ble.bat --extcap-interfaces".
The...
Hi,
Can you please explain what is the usage of unconnectable advertising? And what is the difference between beacons and unconnectable advertising?
Thanks!
What does (15U) mean ? Is that a specific useage declaring a number?
What does " =='\n' " means ?
After a long period of learning , I'm now trying to read and understand...
Hi everyone,
I am making a zigbee mesh with just coordinator and routers only. I intended to have the mesh to cover a very large areas with nodes that can be moved (not...
Hi,
I have got some problem of understanding the IQ sampling data.
As below is the official data format
0: I_Q (default)
Q
31:16
12 bits signed, sign extended...
I have successfully installed the drivers and downloaded the latest firmware version, but the connexion fails and I can not use the AT interfaces command for the modem controller...
Hi
I am using an example project written for pca_10040, I am trying to replace it with pca_10010.
So far, I changed the "Target Device" in the project options and the...
Hi all,
Currently we are trying to measure the power of nRF52832 using (1) nRF52 DK board, (2) power profiler kit 2 (PPK2).
We used PPK2 in source-meter mode and we connected...
