Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
during the test of the trasmission, in my phone I have seen the figure below:
As you can see the trasmission is every 2 seconds and I want to change this time trasmission...
I was looking through the nRF documentation as well as some of the Thread documentation and I was unable to find a definitive answer about the IPv6 fragmentation support within...
Hi
I want to purchase NRF52810 parts pre-programmed with my Firmware. Is this an option you provide and can I reprogram them via the Debug port if required.
Hi,
I am trying to interfacing the IMP34DT05 Microphone with the NRF52840. I can see in the DSO that CLK pulse is generating in the NRF52840, but there no data pulse from...
I am able to switch between two beacon types i.e. iBeacon and a manufacturer's specific beacon when they are both the same length. I am having trouble switching between an...
We have an OpenThread network composed of nRF52840 devices, but we would like to have ensure that Internet access is not interrupted by a power outage. I saw that there is...
In my application I have a current consumption of ~20µA. When I enter bootloader to perform DFU I initialize my peripherals the same way as in my application and I have added...
Hi,
The release notes of v4.1.2 at https://github.com/NordicSemiconductor/pc-ble-driver/releases
mention the fix
"Fixed an issue where USB connectivity firmware hangs...
Hi!
(My apologies in advance in case the information I need is to be found elsewhere. There are numerous tickets related to GPS/A-GPS, but everybody seems to have his/her...
Hi,
I keep looking at different posts and I struggle to understand.
Is it possible to save to flash (nvm) on a nRF51422 with s130 while the Bluetooth is ON and connected...
Is there an easier way to print out debugging statement that does not need an installation of a logging package in keil.
I am trying to place print statements within the...
Hi,
I'm trying to create a Node application (using Noble) that acts as a DFU controller so that I can automate DFU'ing hundreds of devices (nRF52 using SDK 15.0.0). I've...
Hello, I want to use the Nordic Thingy:52 products to extend the Bluetooth range from my phone to a Nordic Development board. How should I start? Any suggestions? Thanks!
Hello
I am using nRF5 SDK ver.16 to try to create a BLE HID touchscreen device. I referenced ble_hids_mouse example and changed HID report map. On Windows 10, it works pretty...
Hi,
I am getting started with nRF9160DK so that I am try to build the application nrf_cloud_agps on segger embedded studio. But I cannot build the application, it says that...
