Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hallo devzone,
i have a real time task, where i have a trigger, different calculations and then the corresponding action.
Now i need to calculate the time from the trigger...
Hello,
As I am new to the world of bluetooth and its stack I have a question which I cannot find the answer for on the internet.
I've read a ton of posts on the devzone...
Hi Nordic Team,
Requirement-
Connect->Send 1 packet->Disconnect->Connect...
I am Sending a data packet to central using Timer handler and trying to disconnect using...
Good day.
I am trying to add flash storage functionality to a project based on the ANT asynchronous transmitter example and the ANT back ground channel example of the SDK...
I am using the nRF51822 QFAAH0 Chip and running it on 90 mAh battery. Currently I am using the AMS1117 3.3v LDO voltage regulator. It is running as iBeacon for 7 hours. I...
Hello Sir,
I am developing nRF9160 based smart tracking device for kids , and i am used only nrf9160 not used nrf52840. so my problem is that how to upload firmware direct...
Hi everyone, I'm a BLE / Nordic Semi beginner. I played around with different examples and most parts of my projects are working. But now I'm struggling with the peer-manager...
Hi,
I'm looking for a solution that will enable me to connect multiple NRF52 modules to AWS-IoT, via a single internet gateway.
The idea that every nrf52 module will have...
Hi,
We need to interface ASDA a2 delta AC servo motor with NRF52840 in our project.In this servo motor i need to get the position value and direction so i interfaced servo...
For the SPM example is there a way to create a DTS or overlay file for the SPM in a way that it does not require files to be added to or modified in the nrf or zephyr repositories...
Hello,
Is there any way i can transmit information from the bootloader to another application using a non volatile memory or non volatile register free for use.
I know...
A while back I was working on I2C and came across the compiler error " 'NRFX_TWI0_INST_IDX' undeclared ", which seemed to be related to NRF drivers vs NRFX drivers confusion...
Dear Nordic Support,
I am using nRF SDK for Mesh version 3.2.0 with nRF52840-DK. I am making 2 devices like the below:
1. First device: the provisioner, able to do PB...
hello, testing the spi examples of SDK16.0.0 I was trying to read a type k thermocouple with a max31856 on the nRF52840dk board, I made the connections of ss, sck, mosi, miso...
hey, i am strating with nrf52840 for thread.
i want to know if there is a need to add an antenna to the SoC? if not i can't visualize where is the antenna in the nrf52 DK...
