I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I'm using the SDK11 and SD130 on a custom board which has a nrf51822.
I connected via SPI to a DSP that sends and receive audio.
My handler of the SPI is as it follows...
I'm trying to send a set of 246 bytes by uart fifo. I have a PC side which retreive the data, but I always miss some bytes (4 to 6).
I'm checking app_uart_put return and...
Hello,
I would like to use the nrf51822xxaa as BLE gateway for an ARM application processor (connected through the UART).
I successfully cross-compiled pc-ble-driver...
Hi..
Can i use both observer and broadcaster roles concurrently in s130 soft device..?
Is any TDMA needed to do this..?
Is it possible to do without stooping the other...
Hi,
I have read the S132 Softdevice specification v3.0 and just want to make sure that my interpretation is correct. There are two scenarios I would like to verify:
...
Hello,
I'm working with a nrf51822, SoftDevice S120 v2.0 and SDK v9.0 platform.
Specifically using it a Central role to connect to a Blood Pressure peripheral.
When...
Hi,
As a beginner, I'm trying to have CDC J-Link Uart port work with my laptop. I'm using nRF52 board. When connecting the board to my laptop (windows 10), it displays...
Need some help on the tcp server example in the IoT SDK.
All steps working but the python script gets Connection refused.
bash# ifconfig bt0
bt0 Link encap:UNSPEC...
(nrf52832 PCA10040)
Hello. I'm trying to go along with the ble tutorial (advertising, service).
I download before last version of sdk 11 because with last 12 it's not working...
Hello everyone,
I have 2 chip; Bluegiga and nRF51-DK
I can easily advertise my custom service in Bluegiga chip. As you can see, nRF Connect application shows my service...
I think one way or the other the struct ble_gatts_evt_t must be correlated with the GATT profile, that is, ble_gatts_evt_t should have services and characteristics as its...
Hi,
> Context:
I run a baremetal application that I would like to enhance with bluetooth.
I am considering a BLE module from NS.
I currently have a SoC (nanopi...
I have created a nRF52 based peripheral device which is used to stream sensor data to a connected central device, usually an iPhone. I can stream data, reliably to the iPhone...
I have an odd situation. I've been using an iPhone 5 and 6 to connect to, and test against, both an nRF51 (redbear nano) and the same code built for nRF52. It works fine....
