I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Is there any S110 demo with good communication between periphera and APP in phone side in SDK 6.0? It means that data channle works well from 51822 to APP and APP to 51822...
Is there any S110 demo with good communication between periphera and APP in phone side in SDK 6.0? It means that data channle works well from 51822 to APP and APP to 51822...
The nRF51 series reference manual v3.0 documents 3 Real Time Counters: RTC0, RTC1 and RTC2 (pp 17 and 109). However, RTC2 does not appear in the SDK documentation (e.g. no...
when I download program(pin_change_int_example) in nrf51822, Immediate Interrupt is occured
And when I push the button, Interrupt is stop...
What is problem?
I want...
Hello,
I am designing a board based on the SoC nRF51822. Since this is a homemade project I do not have lab equipment so I can not measure antenna impedance and therefore...
I'm trying to pull my project out of the examples directory, but there seems to be many dependencies on files far outside my project, and files not shown in my project file...
We use Laird BL600 module in our design. Laird engineers has informed us, that to update softdevice firmware of Nordic nRF51822 chip inside module they use Jlink adapter over...
Hello,
i've already read a lot about this topic in this forum, but now I'm unable to continue on my own. I wan't to migrate the DFU SDK emaple from Keil to GCC. I already...
Hello,
I am trying to use the nrf24l01+. But I don´t get any signal in the MISO pin. I have the same behavior in all my nrf24l01+ devices.
The MISO pin as always HIGH...
Hi,
I'm despair.
I am trying to receive data from the device with nRF2402G with a nRF24L01 + module.
The old receiver is destroyed.
I believe that I have put all the notes...
A long term problem with the Segger JLink drivers on OS X has been that for composite devices, the Seggers with both a JLink/JTag plus a USB for the UART, like those on the...
I am planning to collect data from multiple ANT sensors with nrf51 dk (like heart rate, cadence...) Collected Data will then be transmitted on a different proprietary link...
Hi!
I'm working with a NRF51822 (not a dev card) and I want to disable and enable BLE by switching a switch.
I've been looking at this thread and the functions bluetooth_sleep...
