I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
When programming a nRF9151 firmware on to Thingy91 X, I made a mistake and failed to change SW2 from nRF53 to nRF91 (the label is very small). The USB serial port no longer...
Hi,
I have finished some code with nRF54L15 and nRF52833, now I want to add nRF7002 to my design and I am wondering whether this is available?
Thank you!
Hello, World
Please note that the following questions may be difficult to read as the text was created using a translation tool.
I have downloaded version 17.0.2 of the...
Hello Nordic Team,
I am working with the nRF5340 Audio DK as a central device , trying to establish a secure connection using Security Level 4 (128-bit encryption with LE...
Dears,
I made custom board using nRF52832 and tried to write FW in flash. But I failed it.
*. HW JTAG : J-Link V9+
*. SW tool : nRF Command Line(nrfjprog)
Step #1...
I'm trying to run the 32 MHz SPI00 on the nRF54L15DK to communicate with the MX25R64 flash. However, the clock signal I'm measuring is limited to 8 MHz. Do you have any ideas...
Hi.
I am developing with NCS 2.7.0 using 5340 and have configured it to use 5 generic switches. These work fine. However, the order of the switches displayed in "Home" on...
Regarding the schematic for nRF54L15 DK I currently see on the site that the link to the schematic is disconnected, can you please provide the URL where the schematic is available...
Hello, After successfully building Wi-Fi Fundamentals Lesson 3, Exercise 2 under nRF Connect SDK v2.9.1 & using nRF5340-DK with nRF7002-EK, I get the net_zperf: setsockopt...
Hi,
I think the CPU-Load subsystem in the sdk-nrf for Zephyr does not yet support the nRF54L15 as of v2.9.1 and current main since some devicetree-handles are hardcoded...
Hello, I am test DFU USB function with my Thingy53. So far, I have been able to add DFU USB support from my application but not from the MCUboot. I am using the recommended...
Hello, I am trying to save my sensor data and system uptime to the external flash on my nrf5340dk. So far I have been able to erase some sectors of the external flash, write...
I'm still trying to figure out sysbuild. I want to use sysbuild for a custom board and am trying to build a directory structure so I can flash my nrf5340DK and my custom board...
