After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
IUsing the Master Control Panel application on my Android device to connect to my nRF51822 module (acting as the GATT server), I have implemented the Device Manager (v10 SDK...
I have successfully compiled BLE application using tutorials provided on nordic website.
but when I start doing debugging for better understanding find out that I can not...
I received an nRF5340-DK last week. Today I got the zephyr toolchain configured and working under Linux, and hooked everything up. The "blinky" sample app works fine. The...
Hi,
I'm using nrf52840 with an application which supports both BLE connections with mobile and PC via NFC pad.
the file nfc_ble_pair_lib contains the function pm_secure_mode_set...
The BLEJack nrf51 sniffer firmware is a BLE sniffer/jammer/hijacker. If you google you will find the repo and the defcon presentation.
The author claims you can sniff access...
Hi,
I am facing the issue of sending 8210 bytes of data to my slave device.
I am using NRF52840 interfaced with the MAX32664 maxim sensor hub.
I tried both approaches...
We are thinking to evaluate both the U.FL and Trace Antenna options on a custom nRF52840 prototype board.
1. Referring to this discussion, point 3 is about provisioning...
I want to use mesh configuration ( Bluetooth mesh submodule) to save data to the flash memory of nRF52840. The code works fine and I can save data to flash using mesh_config_entry_set...
Hi, I'm having problems with compiling the gazell_dynamic_pairing example with arm-gcc compiler for nRF52840 Dongle. I have already migrated other gazell and esb examples...
Hi,
I have this generic register read function to handle communicating with my sensor, and during initialisation, it works fine. However, when I try and request a transfer...
Hi! I'm trying to setup mesh network and get data from sensors thought SensorClient SensorServer via ProvisionerNode.
My Nodes info: - Provisioner, UnicastAddress 0x0001...
Hi,
I'm using DSK 17.0.2 on the nRF52840 DK.
I followed the instructions for a buttonless serial DFU:
1. I cleared my board (nrfjprog -f nrf52 --recover)
2. flashed...
Now I meet a problem: when the chip of nRF52832 is power off, but supplies power to one GPIO pin of the chip through resistor voltage division, then I found the voltage of...
Hi everyone,
I'm currently trying to the get UART logging running on the NRF52832, but fail to get the SDK working.
My settings are as follows:
#define NRFX_UARTE_ENABLED...
I want to use GPIOTE implement soft uart on nrf9160 Because it can use interrupt to receiver and data
Any kind man give a example here. that will be thanks a lot
Hi all,
I new to Nordic Semi and recently got started with nRF9160-DK. I've gone through the getting started guide and am looking for suitable tutorials, and examples to...
