Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
I cannot install the app "Programmer" automatically. The connection always fails due to poor network in our country. The error report is as follows:
Is there anyway to...
Hi Community,
printf() (and variants) fail on rounding floats: This is is probably an error in the printf implementation. I tested it with SDK 16.0 on NRF52840.
Format...
Hi,
In addition to listening the advertiser's and beacon data we also need to offer the master application - which is connected to BLE-module via UART - the possibility...
Questions about ‘Application data’ placement in the flash memory
Is there a function or other mean that could give me what is the lowest flash memory address that is occupied...
Hello All,
I am working on the Nrf52810 with sdk 15.3.
When we connect device through nrf connect app (android) i wanted to disconnect after 1 min .
I have given timer...
nRF52840 DK:
ble_app_blinky is working. After that, I flash ble_app_bms, ( working),
then flash ble_app_blinky- the smart phone is not able to discover service .
Any...
When scanning 1MBPS & Coded PHY at the same time, the probability of Coded PHY broadcast scanning is very low, and 1MBPS PHY broadcast can be scanned normally Slave configuration...
i have come across a couple posts related to providing more compatible Altium design files so that other CAD packages can import them. The best articulation of this point...
Hello I have upgrade software and modem firmware and the program using mqtt protocol don't work any more.
Besides the connection to the broker (many error -106), the program...
Hi, Im using a BMD-300 board with the external crystal installed, I can run zigbee examples fine, even using the external crystal, but when running the Mesh examples I can...
Hi
I have some doubts about NB-IoT and I wanted to clarify them before start deeping developing with nRF91 since this module work with this network.
I know that NB-IoT...
Hi,
I use SDK13.1 FDS example and have some questions about that.
Is there any influence about the lifetime of Flash when i use FDS function to write and delete the records...
Hi,
I am a beginner with nrf9160 DK and followed the instruction in https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_programming.html#gs-programming...
Hello I am using :
GNU/Linux Ubuntu 19.10 on a x86 computer
ST-Link v2 that got flashed into a J-Link
Adafruit nRF52832 Bluefruit Feather
Segger Embedded Studio for...
Hi
I am using nRF52832 DK with SES as IDE, on Ubuntu 16.04 machine. I want to send a custom message, let's say "hello" via BLE to Raspberry Pi. I am using some encryption...
