I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
What I want to accomplish
I want to create a bluetooth mesh application. I want one board to act as a server and 12 or more other boards acting as clients. Each client will...
Hello
Im trying to find a way to send multiple messages (unreliable) in a row within a Mesh network in order to measure time taken,
Im using a modified version of the...
Hi,
Please send me if any application code available with RS485 for nRF52832.
Also send if any reference design available for the same.
Thanks & regards,
Arch...
Hello!
We've written a custom bootloader (based off the secure_serial_dfu example), that uses SPI instead of serial communication. I can successfully update an Application...
Hello to all,
We are using nRF52840 with SDK v15.0 using SES, Our application is we have sensor devices with interface WiFi module. Sensor device will wake up as predefined...
I am trying to get a simple spi setup working. Through the dev zone I found a link to this https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160...
It seems like several people have been able to order nRF52840 WLCSP. I checked all of the Nordic recommended distributors but none of them have stock. Would you suggest distributors...
I am trying the demo from github ( https://github.com/andenore/NordicSnippets/blob/master/examples/i2s_master/main.c ) with nrf52 demo board and when checking the signal on...
I am trying the demo from github ( https://github.com/andenore/NordicSnippets/blob/master/examples/i2s_master/main.c ) with nrf52 demo board and when checking the signal on...
I'm following pc-ble-driver compilation steps.
I could run "vcpkg install asio" and "vcpkg install catch2", but "vcpkg install --head spdlog" fails with error:
C:\dev...
Hello, I am usering nrf52840, now i am testing the current. i found that the current is 40uA in 0dBm while 201uA in 8dBm. maybe it is abnormal in 8dBm, what can i do to check...
Hi,
I am using NRF MESH SDK V3.0 ,nRF5_SDK_15.2.0 and with s132_nrf52_6.0.0_softdevice .
I've noted some problems when i try to use the app_timer in repeat mode with a...
Hi, I am fiddling with this example from the SDK: infocenter.nordicsemi.com/in...cp=5_1_4_3_1_2
In this example, there is a test regarding key derivation as:
As I understand...
I am getting intermittent pickup of advertising packet from a peripheral known to advertise every 2 second. Basically I get ~20 sec gaps where nothing is received.
Below...
