Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
In nRF5_SDK_15.0.0_a53641a code, there's such definition:
#define UART_DEFAULT_CONFIG_BAUDRATE 30801920
Which means about 30.8 Mbps.
But in page 345 of nRF52832's...
Hello,
I'm using a nrf51822 board as a DFU controller to update another board's application, the client board runs the bootloader secure example. When I write data to the...
This is almost certainly a noob (to nRF52840) programming question.
I have modified the peripheral/gpiote example to invoke an ISR on the falling edge of a pin signal. In...
I am trying to use the Sparkfun nRF52832 breakout board as a master in I2C communication. I am using Arduino IDE to program the module. I defined pins 24 and 25 as SCL and...
Nordic Support, Let me first explain what I would like to achieve. I am developing a line of devices that will act as GATT peripherals. I would like average current consumption...
I have a custom board with an nRF52832 (CIAA-B0), and I am trying to use the SPI Master.
When I use SPIM1 or SPIM2, the transaction hangs, but the same code talking to SPIM0...
Dear Nordicsemi,
We are looking for Sub 1 GHz RF Module, which gives Longer Range distance in Field either in LOS or NLOS.
Please share the details regarding proven...
Hi guys,
We've written a small test on-top of our internal Bluetooth library (glorified wrapper sat on-top of SDK 15.2.0 SD140 6.1.1) on the nRF52840 to send dummy bulk...
Good morning everyone,
I am implementing a custom radio protocol on NRF52 without using the SoftDevice at the moment. For some reason, I get a HardFault which I am trying...
Hello everybody,
I can flash my custom nRF52832-based PCB using the nRF52 DK and Segger Embedded Studio or nrfjprog, but this requires that I always have my computer with...
Hi,
I need to get 1.8V on the VDD using high power mode. According to the documentation this is the default value. However, I measure 3V.
Please advise,
Daniel
I am developing a nRF-Mesh based product. This product consists of a fixed number of nodes in a Bluetooth Mesh Network. Are there possibilities to factory-provision a set...
Hi!
I am working with experimental_ble_app_eddystone in SDK 12.2.0 for nRF52.
I have seen that the firmware does not support using different advertising inteval for each...
I'm wondering whether or not nRF52840 can be used for a USB smart card development.
"According to the spec of a USB CCID device (which could be found on www.usb.org ), there...
Hello everyone,
After using IPSP intiator and IPSP Acceptor BLE Examples on 2 different kits and connecting them through this profile, how do i send IPv6 packets between...
