Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
IUsing the Master Control Panel application on my Android device to connect to my nRF51822 module (acting as the GATT server), I have implemented the Device Manager (v10 SDK...
I have successfully compiled BLE application using tutorials provided on nordic website.
but when I start doing debugging for better understanding find out that I can not...
Hey,
We got a problem when trying to figure out how to detect the custom services from Unity. We are trying to read data and afterwards to do some manipulations of objects...
I am new to Nordic and want to design with the nRF52840. I have read this guide:
used AppCAD to find the best width and clearance for the ground layer, but when I downloaded...
Hello, I am using NCS 3.0.2 on nRF52840. I have been using MCUBoot for a long time on my device, and it is working fine. Recently, I went through a requirement where I needed...
Hey everyone,
I've been trying to get the Bluetooth Mesh DFU Target sample working on my nRF5340 DK and running into some issues. I've read through the docs.nordicsemi.com...
Hi All,
I have an nRF5340 Audio DK which has problem with the network core. When I connect the USB to board or try to recover the board the MCU light at the bottom of...
Hello all,
I am working on a project with 2 nrf5340 Audio DK's and I want to have the same functionality of the walkie talkie demo but instead use the microphone of the...
I had a working Matter application, but due to some human error, I erased my WSL installation.
I set it up again, but after successfully flashing my code onto the Nordic...
Hi,
For a product currently under development, we need to use a counter as an RTC. We’re targeting the following commit in ncs/sdk-zephyr :
github.com/.../d7e41fd2e361ee15454a253ebec9bb37aceaf09f...
Hello Support Team,
I am currently testing the new Channel Sounding feature on two nRF54L15 boards, on which I flashed your Channel Sounding samples ( initiator and reflector...
Content: I’m working on integrating the nRF7002 EK over SPI with an nRF54L15 using nRF Connect SDK v3.1.1 . While setting up the workspace, I noticed that the Wi-Fi driver...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
I used the nRF Audio Example to build a BLE audio device. I use the test tone generator functionality. I was previously using nRF Connect SDK 2.6.1 and the test tone generation...
I am an FAE with Ezurio, we have a customer who was running through the nRF Connect SDK Intermediate training on DevAcademy and they ran into issues with AuTerm in Lesson...
## Description
On the nRF54L15DK, the measured floor current increases significantly when the GPIO is configured for button edge detection.
### Observed Behavior
* Floor...
Hi,
I am quite new to nrf's and zephyr and I'm working on a product that requires Direct Test Mode functionality. I started with the DTM sample and am now looking at how...
Why do I often fail to compile the examples due to west? The prompt suggests that I need to upgrade west, but I am unable to do so?When directly upgrading West through VSCode...
