Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
I am using a thingy52 device and in that, added code of advertising and scanning from the sdk 16. Advertising is run successfully. But getting packet loss issue. So, I am...
Hi
Im developing an application that will wake up on RTC every 15 minutes. My issue is that when using idle_state_handle, which in turn calls sd_ble_app_wait, the RTC...
Hi,
Trying to figure out the current requirement on GPIO input, can you point me in the correct direction in how to figure out how much input current the GPIO on nrf9160...
Hi,
we are planning to add a 256 MByte NAND flash to our sensor project. I saw the example for NOR flash on the PCA10056 which is working fine. But due to costs we want...
Hi,I am using the nRF52840 development board, S140 and SDK16.0, I have some questions about data transmission on the UART.
I am trying to make a central device that is similar...
Hi,
I am working on a custom nrf52840 board and am having trouble connecting to the usb interface on the chip. After testing with the dev kit, the adafruit bootloader...
I trying to establish communications with a (non Nordic) beaconed 802.15.4 coordinator.
I've used some code from the wireless_uart_raw example but did not use the FSM. ...
Hello all,
I am having a problem to get SAADC to work with low power. I am using custom board with chip NRF52811, SDK 16.0.0.
I had turned on the SAADC_CONFIG_LP_MODE...
Hello Everyone,
I am using my custom board with nrf52832 SoC and developing my application firmware with sdk15.2 & softdevice v6.1.0.
In my application code, BLE scanning...
Hi,
We were trying out the LTE RX/TX test using the AT%XREFTEST command and undestood that for LTE RX testing ,an external signal generator is required. Is there any way...
Hello
I would like to know if there is a capability of a truly secured boot with the nRF53, starting with a secure bootloader in some locked or immutable memory - i.e. secure...
Hi team
I did follow the getting started assistant to set up software tools and clone sdk ncs 1.3.0.
Verified successfully at getting started assistant, too.
But, when...
Hi
I have some issues with nRF52810.
I am trying to use SPI as a Master on a custom board. I saw here that nRF52810 does not support legacy SPI : https://devzone.nordicsemi...
Hello,
We are adding BLE scanning to an ANT product.
We have been using SDK 10.0.0 from the beginning, so we use the Example below.
SDK 10.0.0.0\examples\ble_central...
Hi Supportor
I have two board, if I didn't set the gain, which used default of SDK, one board output value is 0x2f5, another output ADC value is 0x266.
I set the gain...
