I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I have a lot of issues when switch to using nrf52820.
all saadc module seems removed from the sdk, or forget to add to nrf52820.
when using softdevice, get a log of...
Dear,
When I click the "F5" key for debugging after complete compile, it requests some files as below.
Could you let me know why it requests and how to fix it?
hi. I use sdk16 and ble sample like kb or mouse. i want to save some data in ic. with flash_fstorage.
i see flash_fstorage example .it can use SOFTDEVICE_PRESENT for save...
Hello,
I am trying to find a way to upload the certificate automatically from the main.c file instead of uploading them to LINK monitor. Is there a command in nrf project...
I have a known working distribution (ZIP) file that when flashed onto a device, correctly goes into the application and is able to do buttonless DFU. This was left behind...
hi all:
NRFSDK_16. I want to get timestamp from rtc,but my device need run with low power,so when the device in idle mode(no user use),will put it in system off mode.
...
Hi, Nordic,
I have the follow questions in the nRF5_SDK_17.0.0_9d13099
1. Why in the Demo ble_app_multirole_lesc remove the BLE_GAP_EVT_LESC_DHKEY_REQUEST's process as...
Like --insecure option in the curl command, i want to skip certificate validation when make a https connection to server, so i have checked all http files in zephyr and there...
Hi everyone,
I am new to programming on such an embedded device(NRF52840DK). I met a problem recently of how to set up the PIN on the board to connect with the LPS22HB sensor...
According to the doc; * This function will block until the temperature measurement is done. * It takes around 50 us from call to return.
Instead I'd like to return the value...
Hi,
I’m developing an application using the SDK V16 , the nRF52DK (52832) as central, and a couple of Sparkfun nRF52832 breakout boards as peripherals (both peripherals...
Hi everyone!
I am trying to implement the OTA - DFU in my project. I have my own board with a nrF52832 chip.
The project was build using SDK 13.0.0 and softdevice s132...
Dear Nordic Support Team,
I was using the CoAP and MQTT components in nRF5 SDK v16.0 .
So my device was able to do CoAP and MQTT via BLE 6LoWPAN. Adding a BLE service...
I am following the turtorial in the Github and build a project which add a custom service. The project can read, write and notify between the board and mobile nRF connect...
