Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
Hi Everyone,
I'm not able to start ble scan. I've followed following example...
Developing Bluetooth Low Energy products using nRF Connect SDK
https://www.youtube.com...
Hello,
I was trying out sending RR intervals on the Heart Rate Measurement service and seeing what happens in nRF Connect. But, something is weird with the way the values...
I have a client project developed in 9160 which needs to be connected to the network via NB or LTE-M. Before each connection, I read imsi to determine the apn of the carrier...
Hi
Im trying to get the mcp2515 candriver example to work https://github.com/nrfconnect/sdk-zephyr/tree/main/samples/net/sockets/can#id3 .
i have some error during build...
We have an nRF52 with dual roles: peripheral for the connection to an app, and central, connecting to multiple third party peripheral devices.
We have come across a very...
Hello,
I'm using Segger Embedded Studio (SES) (on Windows 10) with nRfConnect SDK and nrf5340 processor.
In SES I can oben a graphical view of the configuration through...
Hi, I have developed a firmware on nRF52840 as central ble_app_uart_c\pca10056\s140. Now I have to upload it in nRF52810 which soft device should I use? Thanks!
Hi all,
I working with NCS v1.7.1 on a custom board using nRF52840 and I am trying to enable a 2-stage bootloader setup using NSIB as the first stage immutable bootloader...
Hello sir,
I am using the nrf52832 Dev board and try to send the data through custom value update then the following error occurs as ERROR 8 [NRF_ERROR_INVALID_STATE].How...
P0.25 is accessible by below:
nrf_gpio_pin_set(25);
However, when I try to access P1.00: Neither this:
nrf_gpio_pin_set(1); Nor this works:
nrf_gpio_pin_set(32);...
Hello, we have a device that uses the nRF9160 with an external GPS receiver that is controlled over I2C. I have connected the LNA enable pin to COEX0 on the nRF9160, but it...
Hi,
I was evaluating 9160DK. I tried the GPS example using 1.7.1 SDK and it works great outdoor. However, I tried to use a hackRF one to emulate the GPS signal. 9160 shows...
Hi
I still have a number of devices that are based on nRF24E1. From time to time the chips need a change in firmware. Since the last time I updated them, my PC has crashed...
Hi support team
I have been modifying the throughput example (nRF5 SDK v17) to connect the receiving unit (AMT client) to more than one device. I am running this on the...
