Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
Hello.
I am developing with nRF52840DK.
Normally, I think that the buck regulator supplys 3.0V to Interface MCU and nRF52840.
I want to connect the 1.8V peripheral...
We're working on an nRF52840-based project that started development on SDK 17.0.0 and Softdevice S140 7.0.1, but we wanted to get it to the latest release before production...
Hello,
I am working on Arduino's platform and decided to ditch the ArduinoBLE.h library due to its overhead.
I would like to send high frequency (2Mbps per the spec ,...
Hi,
I've trying to get the Omnivision OV7670 to work with the nRF52840-DK. I'm not completely sure whether I've configured it correctly. My pin assignments are adapted from...
Dear,
we have found a strange behaviour when using the DTM in SDK 17.0.2 and 17.1.0. The problem starts from ble_dtm.c:1188 when comparing the parameter value with -30dBm...
Using SDK 14.0.0 with SD 132 v5, the device name I'm advertising with here is "000000DK". But the advertising module is truncating it to "0000". It will do this if I have...
Hello,
I want to use 1M baud rate in nRF5340 DK board.
DK board is connected to USB to Serial.
Until 921600, UART is received correctly. And UART is broken in 1M....
Hello,
I have been using NRF Connect SDK 1.6.1 with Microbit V2 to run some zigbee projects! Now when I should build some new firmwares I upgraded to SDK 1.7.1 and after...
Hello, I have an nRF52840 custom board and SDK 17. I want to make a project with a buzzer control. I am trying to find a suitable sample project to start developing my own...
Hi everybody,
I am working with an UART example with multi-link and everythink working on coded_s8. The objective is keep 20 devices connected and every peripheral send...
Hi Tech support:
I am using the latest Desktop nRF Connect(Windows version) tool. And I want to use it to connect to my nRF52 DK board and setup up an advertising setup...
Hello,
for our application i need to periodically enable and disable the openthread stack on the nRF52840 chip.
For testing purposes i've modified the Thread CLI example...
Hi,
In my application i am trying out to transfer data in Long range BLE_GAP_PHY_CODED mode , i have set my peripheral has to advertise in PHY coded mode below is the advertising...
Hello,
We are using nrf52832 in our development, we recently got the otii arc to measure the power consumption of our device.
During sleep mode we notice a huge spikes...
