I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I working on a BLE app with 2 custom services.
When I try to expand a characteristic I get a spinning indicator below the characteristic and after a while I get...
in nrf5 sdk 17.0.2 example\ble_app_hids_mouse , hid map
correct is 0x95, 0x05, // Report Count (5) is five ! is five
Forgive me for just reading the comments at first...
Hello, I'm using nrf52832 and i need 2 UART instances in parallel. I get an error when I set the second UART.
Do you have an example using 2 UART instances in parallel?
Hello,
i am new to the topic and am looking for tutorials, additionally to the nordic examples and this community.
I found the following website:
https://embeddedcentric...
Hi,
When a board is connected to debugger, It works well for 2 hours.
But when it is detached debugger, It looks like stuck to POWER_CLOCK_IRQn after 4~6 min after power...
Hello,
I'm trying to make a one-shot MQTT publisher and I'm able to get 22 messages published but every time I try to publish the 23rd the code hangs in mqtt_transport_write...
I'm not able to get a response using the new CONEVAL AT command. I'm using firmware v 1.3.0 and a recent B1 variant nRF9160. Response is always ENOEXEC. I have tried before...
Hello,
In my project, nrf_drv_gpiote_in_init is used 3 times.
battery measure
sleep trigger by motion sensor
wake-up trigger by motion sensor
After 3rd call...
HI
I am trying to interface ads1231 with nrf5340. Regards I need to know about Gpio read. Because ADS1231 gives digital output. I don't know how to read actually. Kindly...
What is the purpose of the ble_advdata_encode() method?
I see it has been used in the beacon example, but some other examples don't use it.
In both case, the advertising...
Hi, all..
An error occurs as soon as it connect and disconnect through advertising. Timer interrupt is currently running on the main function..
and then I found error...
OS: Mac
I installed nrf v1.2.0 and Segger Embedded Studio v4.42a. I can't open project and it causes error.
I can open projects with this config on SES v4.42a and...
Hello,
I installed Segger Embedded Studio v 5.34a following the online instructions AND the Getting Started Assistant instructions for a Mac. I then tried to import a project...
Hello everybody,
I'm trying to develop mesh network with zephyr, but the problem is that logs are not displayed in SES debug terminal. In autoconf.h file I can see that...
Hi,
I have been following this post and did all the steps instructed by , but I failed to receive a response in Tera Term in the end. I have also tried changing the hostname...
