I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello,
I have a project based on Cloud Client v1.4.0 using AWS IoT cloud as the backend. I have made some changes in the code so that I disconnect after sending some values...
The frequency tolerance for ANT stack for an external 32.768 kHz crystal oscillator should be +/- 50 ppm max.
Does it mean over temperature range?
There was the same question...
HI:
Now i am use the OTS to transmit image, if we want to set the MTU=185, how many paramter must config here?
example:
CONFIG_BT_CTLR_TX_BUFFER_SIZE=185 CONFIG_BT_CTLR_DATA_LENGTH_MAX...
Hello, I have created my own C program (in eclipse) that basically should just initialize to an LTE network and connect to it, nothing fancy at this point.
I have come across...
Hi, I tried to set up the environment for the nRF Connect SDK v1.5.0 using nRF Connect for Desktop on Ubuntu 18.04.
In step 2 (Cloning the SDK), I got some errors while...
I use arduino to program a nRF52832 board. I had problems to move a running project with a ST7789 SPI display to the nRF52832. I use the Adafruit lib to drive the display...
Hi,
My custom card has ic nrf52832QFAAE0 AND NRF52DK has ic NRF52832QFAAE1.MESH SDK EXAMPLES runs properly on NRF52DK but not working on my hardware with ic NRF52832QFAAE0...
Hi,
What cellular connectivity, the provider's DNS, and backend cloud services, invariably connecting over MQTT is transient and the internal blocking timeout of mqtt_client_tls_connect...
I'm using Zephyr on a nRF52840 and I'd like to use the QSPI with the Fat Filesystem. I added the following Config statements to prj.conf:
The nrfx QSPI driver and file...
Hello,
I am wondering where to change the baud rate for the UART in the NRFConnect SDK using zephyr. I am working with the peripheral_uart example.
Thanks,
RJ
Hello,
i just migrated from nRF51 to nRF52. I tried to implement my custom service. I followed the tutorial from this site: https://github.com/bjornspockeli/custom_ble_service_example...
Hello,
in our application we have two devices. A nrf52840DK as central and a BMD-300-EVAL (contains a nRF52832 chip) as peripheral. We need a timer/counter that generates...
Hi,
I had used nRF Connect Programmer to flash nRF Sniffer firmware on my nRF52840 Dongle, but after that, when I tried to flash the firmware again, I found that there was...
