Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
hello Nordic
i am working on nrf52840, SDK16.0 developing on the peripheral app_ble_blinky example.
i am use a pin as input interrupt from other device,
if i does...
Hi,
My application uses the nrf9160dk and I program 3 Zephyr images onto the 52840: (1) bootloader, (2) image1 and (3) image2. There is no SD or anything else on the device...
Hi, I have a holyiot NRF52840 dongle (schematic below). I am able to program it via the swd interface and have BLE examples running (as long as power is attached to VDD),...
I have an application that is running the following setup as a multi-connection (peripheral and central) setup:
I am having an issue when a peripheral (NUS) is sending...
Hello everyone,
I am going to run the mesh DFU example. I found that I must use Python2, not 3 to work correctly. I follow the instruction suggested in this post.
https...
Hello, i don't know how build many project with other configuration. I want to do a lot of configurations.Then for each of them make hex files with one click of a button....
Hi
When I try to build NCS sample using SES (v5.40, also v5.30a nordic edition) it seems to build the project correctly (.elf, hex are generated) But it throws error at...
I am trying to bring up an application that uses the soft device, but not right after power up.
I want to use an application timer to schedule a timeout say 10 minutes after...
My project builds when set to Release, but fails when set to Debug. Here are the last few lines of the transcript output:
1> "C:/Program Files/SEGGER/SEGGER Embedded Studio...
I'm looking to store a batch of data in a large array in RAM and send them all at once later. I start from ble_app_template in sdk examples and add an array. My memory setting...
I'm trying to get LPCOMP working on Zephyr - I have used the vanilla NCS sample as a baseline and have set up the event handler and the init function.
The problem is that...
Hi,
I recently bought a couple of HolyIOT nRF52840 modules for a personal project (building a keyboard). I also got a JLink Edu Mini to flash/debug it. I am able to successfully...
Hello,
I've seen when ADV interval is near than 1 second, the sniffer cacth the same adv twice in diferent channels, but if the adv interval is near to 50 ms the sniffer...
Dear all,
I managed to implement custom firmware using Nordic proprietary protocol (both 1 and 2 MBPS) on nNRF-52840-DK. I would like to know if some spread spectrum tecnique...
