I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Dear all and Nordic Staff:
Thanks for your support as usual.
I have a new application project with BLE and Zigbee dual stack protocol for industry market.
May you suggest...
One of the nRF52840-DK (PCA10056 v2.0.0) we are using as a programmer and debugger for our custom board has started repeatedly resetting the custom board whenever an RTT console...
ble_gatt_db.h and ble_db_discovery.h each contain #defines that are problematic, BLE_GATT_DB_MAX_CHARS and BLE_DB_DISCOVERY_MAX_SRV respectively.
Of course, one can change...
We use NRF52832 in the remote control of the car。 We measured the average current of power consumption at about 1uA.Every 300ms, the current curve bounces to the transient...
I would like to use the RTC in the nRF52833 as a clock-calendar. The device will normally be powered by the USB Vbus but must have power fail protection to insure the integrity...
Hello,
I would like to create a star network (with no routers) in ZigBee with nRF52 (also with multiprotocol BLE). I examined the relevant SDK (nRF5_SDK_for_Thread_and_Zigbee_v4...
My setup is a custom board with the nRF52832 and a remote BLE client e.g. nRF Connect tool kit on an Android phone.
The application periodically broadcasts a 'beacon' but...
I am using Nordic SDK v15.3.0.
I have set all the required parameters and content before I call the API "ble_advdata_encode(..)". I ran into two issues one of which I can...
I am using SDK version 15.3.0 and would love to know what exactly is the meaning of the first parameter "size of event" used in the macro APP_SCHED_INIT(X,Y)?
I treat "events...
I have installed Segger Embedded Studio for ARM V5.32a.
I am trying to build the example project under ble_peripheral/ble_app_uart.
I have installed these packages in...
Dear community, Dear Nordic engineers,
For some reason I cannot connect my custom board to the nordic cloud. Previously I have followed the described procedures with the...
Hello,
I have a custom nrf52832 board with a SparkFun HX711 load cell.
I've developed my firmware using Segger Studio testing my data through a BLE connection with the...
Hi,
I ported my application from SDK 12.3 to SDK 17.0.2. Unfortunatley it isn't running on the board, but the only thing I have is a warning which I'm hoping is the issue...
