I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello,
I have been trying to setup timer counter for nrf9160dk using the sample I have attached but for some reason the timer value is always read as 0. Not sure if the...
Hi
We are thinking about migrating a project to the nRF52805. One of our concerns was that the nRF52805 may have no "legacy" UART and only supports the UARTE, which is much...
Hey There,
The problem I have is the following:
I am able to open a Port via Putty and C# Script. I set it up like I found it in the docs. ( https://developer.nordicsemi...
Greetings,
If I send empty line (CR or CRLF) to the modem AT port, modem freezes.
Firmware version: 1.2.1
AT%SHORTSWVER %SHORTSWVER: nrf9160_1.2.1 OK
User application...
Hi,
I have developed succesfully an HTTPs client but I am facing a problem related to a relatively long response from the server when I issue a GET request. After the GET...
Hi,
When I try to update the modem firmware I get this error Errorcode: CouldNotCallFunction (0x9) Lowlever error: Unknown value (ffffff24). See attached picture bellow...
I have a issue with nrf21540 in the Transmit state after the Receive state with using of GPIO for control Transmit / Receive switch.
I'm doing next steps for reproducing...
Hi,
I am trying to use the thingy91 to publish some sensor data to an Azure IoT Hub, I've tried to look at mqtt_simple and modified "asset_tracker" application but I couldn...
Hi Team,
This Query is regarding HF frequency Crystal settings, how to configure the nRF52840 Evaluation board to different frequencies. Actually we need to test the crypto...
Hi there,
I'm attempting to link in a static library archive to my nRF52840 targeted project and receive the following error: Exception table sections and plain sections...
when I use Jlink viewer for tracing, found a fatal error:
1 code:
static void lfclk_config(void) { uint32_t err_code; NRF_LOG_INFO("enter lfclk_config"); err_code = nrf_drv_clock_init...
I have been playing with the nRF5340 and specifically the HCI-RPMSG.
I have looked at these files below. They all worked when programmed in the nRF5340.
When viewed in...
Folks,
System Info : MacBook Pro (10,1; 15" Retina, Early 2013), Running macOS 10.15.6 "Catalina", with 500GB SSD, formatted with APFS, into a RO system partition and a...
I've made a circuit using the NRF8001 but slightly deviating away from the original PCB example. I'm getting the device to go into "Advertising Started" but I can't pick up...
