I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
I'm using a Nordic nrf52840 based dongle to sniff the connection to a gamepad. When I bring up Wireshark connect options, it shows dashes in the promiscuous column, which...
Hello.
We would like to experiment with the various Bluetooth IO Capabilities settings with nRF SDK 2.1.3 on an nRF5340. Our project was developed by starting with the nrf...
Hi,
I understand it is possible to profile a battery larger than 3000mAh? That said I've tried to modify profileSettings.json but the nPM PowerUP v1.3.1 seems to ignore...
Hello, on the nrf52840 board,I have been trying to write code to send byte from nrf52840 to my nrf9160. for some reason, the same code works when trying to use uart1, but...
Hi All,
I am trying to print out floating values for my NRF5340 v2.4.1 SDK project. But, I am not able to print out the floating values. I tried the setting the following...
Hi,
Form the past few days, I've been trying to modify the device tree, but the changes are not reflected in the visual device tree. I’ve tried this on different laptops...
I have the following setup in my overlay file:
relay { compatible = "gpio-relay"; relay1: relay_1 { gpios = <&gpio0 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; label = "DC Mtr...
Hi All,
I am using ' NRF SDK v2.7 + NRF5340 DK + VSCode ' and cloned a official nrf ' blinky ' sample. The code and pins are working fine and I have verified using DK...
Hello,
I can retrieve the data from the Thingy:53 via the bme68x_iaq program. However, I don't know and I can't read the data via BLE on my phone via nRF Connect. Do you...
Hi everyone,
I'm encountering a usage fault on the nRF52840 Featherboard when trying to connect to a network using OpenThread. The issue arises specifically during the execution...
Hi,
I am using the Create a new board function to specify a simple nRF52840 based board with GPIOs using nRF Connect SDK v2.8.0. No matter how I answer the questions in...
I'm using the nRF21540 DK with the Power Profiler Kit II in ampere mode for measuring current draw. I had the gain set to +20 dBm for testing but I noticed the system was...
Hi,
We have five NRF5340DKs with us and off late it seems three of them does not get detected by the PC. In fact, what i understand is that the interface MCU seems to be...
Thingy:91X rev 1.0.0
NCS 2.6.2 own custom application
Quiescent current measured with PPK II and extension board:
nRF53x 2µA, OK
nRF70x 0µA, OK
nRF91x 17µA, OK ...
Hello,
We are in the feasibility phase of updating a product to include a nRF9151 modem connected to a nRF52840 via a single UART. The modem will operate in SLM (Serial...
