I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hi,
I'm a bit confused regarding the DFU process for the nRF5340: Under what conditions would the interface between the application core and the network core change?
I...
I am using the Nordic Semiconductor Power Profiling Kit II to measure the interval time of a periodic activity of a target device by monitoring the power consumption and measuring...
Our system has SPI and I2C. Each of these communications works in isolation, as implemented in our program, for multiple transactions. When we try to include both we noted...
On p. 62, section "5.3.10.1 Device startup times" of nRF52805 Product Specification v1.4, the startup time of the nRF52805 is discussed as a function of the capacitance to...
Hello,
We use nrf-connect-sdk v1.9.1 (Zephyr v2.7 LTS)
We have a set of network devices. Both routers as sleepy-end-devices.
The sleepy-end-devices connect to the...
how to set bt tx power in NCS
I referred to this example "hci_pwr_ctr", but err occurs:"Set Tx power err: -5 reason 0x00", Possible errors are BT_SCI-ERR_SUNKNOWN_CMD。 ...
Running NRF52840 mcu core on custom board using 17.1 SDK
1. Use the nRF Connect Mobile app to connect to our device over BLE
2. Run the dfu uploader to update FW from...
I am planning to modify the SLM application (NRF9161) to load its own certificates for TLS upon startup. This should be doable via modem_key_mgmt functions.
However, NRF5340...
Hello,
After migrating from NCS 1.8.0 to the latest NCS 2.7.0 version, I am no longer able to disable PRINTK , which we previously did to reduce flash memory usage, as we...
Is the nRF 5340 already FCC Pre-Certified ?
When we integrate the nRF5340 SoC within our product, should we need to get our product certified by FCC ? is there any difference...
hi professor,
The npm1300 is used for power management on my borad.When VBAT and VBUS are connected simultaneously, the bulk 2 output power supply varies between 1V and...
Hello,
I used VSCode debug for APP core without any issues.
But I cannot debug NET core because, APPROTECT is turning on. I want to disable APPROTECT persistently for...
Hello,
I freshly installed nRFConnect 5.0.2 in a Windows PC. Installation was fine.
When I start it I get an error:
How can I overcome this?
BR Matthias
I am currently trying to use my nRF52 as a BLE central to connect to a OBD II BLE Device. I am able to use the name scan filters and connect here
After connecting, I...
