Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
Hello, I'm working on my Senior project for school and it involves me creating a PCB that will be utilizing the NPM1300_QEAA. Is there a footprint model for it in Altium,...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
Hello,
I am using the same hardware, and firmware on 4 custom boards of the same device. I observed that I am getting different current consumptions in each devices.
I...
Dear colleagues, I am using the Nordic nrF9151-DK as part of exercise1, lesson 2 of the intermediate Devacademy course. Lesson 2 is about trying and using the various vscode...
Hi team.
Now i'm use soc nrf5340, and the ncs version 2.9.0.
I want to encrypt my external flash using QSPI.
I encountered some problems while using the nrf connect...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hello! I'm trying to make what initially seemed like a straightfoward program - a bluetooth-to-hid adapter. Since Nordic's sample (BLE Central HIDS) uses the hogp and bt_scan...
I’m working with a device that communicates over single-wire UART (half-duplex), where TX and RX share the same line (because the peer device is designed that way). Now I...
I am getting a bt_hci_core: HCI driver open failed (-11) with a custom board using nrfConnect for VS Code and 2.9.1 toolchain/sdk.
The code is really simple (I'm not...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
I am working on project using thenRF9151 board and I require the GNSS functionality to work for the same. However, my board is not able to latch on to a satellite network...
Are there any specific points using the external flash of a Thingy:91X?
I tried to adapt the "nrf/samples/cellular/modem_trace_flash" by adding an overlay copied and modified...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hi,
I receive the following build error: "../zephyr-project-v4.1.0/modules/crypto/mbedtls/include/mbedtls/check_config.h:96:2: error: #error "Unsupported partial support...
I found some examples on dev zone how to read RSSI during connected state:
Function report RSSI but as a positive value around 230. How to recalculate it to dB. I see...
