Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
I have TWI sensor comms running fine in Zephyr on nrf52840_dk and separately Bluetooth controller in low latency mode using S140 softdevice also running fine in Zephyr on...
In SDK For Mesh 4.1.0 the Light LC/CTL/Lightness models were added. The problem with this addition is that another flash page is reserved for the models metadata and possible...
Hello,
I am trying to send something by my own via UARTE0. This is only for testing/learning purposes:
This is what I see:
[00:00:00.000,000] <info> app: enable...
Hi,
Can I control warm light as well as cool light using the CTL+LC server example provided in the Mesh SDK v4.2? Or does it support only warm light?
Moreover do we...
This is my log
Loading solution asset_tracker.emProject Executing load commands cmake -GNinja -DBOARD=nrf9160_pca10090ns -DBOARD_DIR=C:/Workspace/nRF9160/ncs/zephyr/boards...
Hi,
Currently I am setting up my work environment. I have a simple Zephyr project running on our custom board with the nRF52840, so a modified example and a custom board...
Hi Folks,
I am currently working on a BLE configuration composed of two NRF52840 chips. One is configured as central and the other as peripheral and use coded phy (long...
While I am going to pair with my android 9 Asus mobile phone with SDK 17 nRF52840. It in my mobile showing "Pairing rejected by Nordic_HRM". After that I have added a some...
Dear community,
I am trying to implement a custom service, however I am struggling because many example codes are for PCA10040, Softdevice S132 and/or for older SDK's. I...
Would it be possible to get the SHA256 hash for version 5.1.0 of the S132 soft device for the nRF52832? Just want to verify the integrity of the download. Thanks.
Hi All,
I am currently designing my PCB using nRF52840 chip.
I was using the footprint downloaded which was in nRF52840 dongle pcb library given by Nordic. During DRC...
Hello,
I am using Nrf51822.
I am using sd_110/application/bootloader, etc. in SDK_10.0 without problem.
Recently, migration to SDK_12.3 / sd_130 is in progress to...
How wide are the peaks? I know that it depends on many factors how high and long the peaks are. Currently we have measured peaks of 450 mA for 40-50 ms in our application...
Hi,
I am trying to run the Zephyr BME280 sensor sample application (using nRF9160 DK) in NCS1.3.1, but get the below error:
My prj.conf is as follows:
And board...
Hi all:
I install "nRF Connect SDK v1.3.0" by Toolchain manager,
but it always show "Failed to clone the repositories".
Could you have any suggestion?
best...
