I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
I'm using the NRF52832-QFAA-R and currently I'm struggling to get the device to connect to a J-link. The nRST line for some reason is being held low even with a pullup. There...
To the kind attention of Nordic support team,
I have got legacy code to work with for nRF24LU1. Radio packets payload and receiving pipe are retrieved using if(gzll_rx_fifo_read...
Hi, I am using nrf52832 Development Kit and SDK( nRF5_SDK_15.3.0_59ac345 ) in that I am working on ANCS and NUS together and specific functionality working smoothly when the...
I have read many of the posts about applications not running stand alone, and have tried many of the suggestions without success. My application runs on a nRF52832 it is being...
Hello,
I am new to embedded programming and I would really appreciate any guidance.
I am using NRF52832 that will interface with I2C USB charger BQ24295 ( http://www.ti...
Hello, I am working on Bluetooth mesh application and i am using nRF52832/40 for the development purpose. I wants to create one independent library with its own data section...
I need to burst write the DMP library into the mpu6050 but not succeed.
The following is the function that I've been using to burst write.
I have researched on the...
Hi,
We developed our device with KEIL 5, SDK15.2 and SoftDevice 6.1.1. After we upgrade the SDK on our device from version 14 to 15, our IOS phone encountered the following...
Dears:
I'm testing the USB mass storage example: \examples\peripheral\usbd_msc with Nrf52840DK and SDK v15.3.0.
Now I have one question. When I plug in/out USB to PC or...
Hi
I am using the NRF52832 ,my code is based on the ble_app_hrs_freertos example sdk 15.0.0
I have one main task which usually run 64 time every second using the vTaskDelayUntil...
Hi I have a module that is used in a hand held instrument. It contains the nrf52832. It connects to phones for data communications. Is it possible to determine the strength...
Dear All,
I am trying to compile and run the ncs/zephyr/samples/drivers on the nrf9160_pca10090ns. For this reason, I have copy-pasted the file under the ncs/nrf/samples...
Sorry, I want to ask that if I can send Decimal(like accel x,gyro x) by the ble characteristic to the nrfConnect, when I send the information, it always becomes hexadecim...
Dear community members
I have end nodes with nrf52832 (Soft device s132) that can communicate to a central nrf52832 DK in Connection mode based on ble app uart and multiple...
hello, I'm develop use nRF52 SDK15.3 template to measure water press, and gyro value.
but in nrftoolbox app just show signed value, so i want to show signed value.
please...
