Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
Hello,
In nRF5340 I use one RTC and it works. Here is my code:
1) in prj.conf:
CONFIG_NRFX_RTC=y CONFIG_NRFX_RTC0=y
2) in the code:
a) define: nrfx_rtc_t sti_period_rtc_0...
Good morning,
I am using the nRF9160 as an AT command modem running the SLM app. I aim to set eDRX and disable PSM (PSM doesn´t make sense in our project). According to...
Hi all,
My team and I are evaluating some BLE modules available on the market. One of them is the UBLOX BMD-340, which contains the nRF52840-QIAA SoC.
We are encountering...
Hello Nordic Engineer,
I have already implemented a Mesh network using iOS nRF Mesh, 5340 DK, and 52840 DK, with the mesh_light example.
The NUS I used before was able...
I am trying to flash the Enhanced ShockBurst (ESB) example on an nRF52840 USB Dongle (PCA10059) . Since the ESB example is originally designed for the PCA10056 (nRF52840 DK...
Hi all, need to establish a CIS connection to an already connected BLE device with security level > = 2 . However when the ACL connection has security level > = 2 and the...
Hello, We're developing a project on a custom board based on nRF52832 and noticed that P0.20 is high on powerup, even with no firmware. Is there a way to controll the pin...
In the nRF5340 Audio DK example located at C:\ncs\nrf\applications\nrf5340_audio , I want to add a third board and communicate with it from the master (gateway) to send commands...
How can I read the whole advertising packet when are packets larger than some specific size? This is the issue. I want to read this adv packet:
But I only get this on...
we have 6 custom board with nRF52840 we are able to flash test codes in 2 boards , while 4 boards give
Error :No Cortex-M SW Device Found . this is in nrf sdk .
when we...
Hello,
I am new to Bluetooth. I have two nrf5340 LE Audio SDKs which I have been able to configure and use as gateway and headset (walkie talkie, USB, and line-in, CIS and...
I have updated a board (NRF9151DK) from modem FW 2.0.1 to 2.0.2. The board is also equipped with nrf7002-EK, and the support for the wifi driver is enabled (SB_CONFIG_WIFI_NRF70...
Hi Team,
I am currently exploring AI/ML solutions for our edge-enabled product development projects, particularly focusing on wearable devices with small footprint SoCs...
