Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
We evaluated the BLE Mesh DFU performance on the nRF52840 and observed that transferring a 342 KB binary took approximately 36 minutes. This aligns closely with the documentation...
Hello!
Can you map the zephyr versions to the LTS versions if possible?
We are using NCS 3.02 with the zephyr version 4.0.99. How does this relate to any of the LTS...
Hello.
I am developing in the following environment. ・nrf52832 custom board ・nRF5 SDK v17.1.0
This program already supports BLE communication, BLE DFU functionality, AD...
Hello.
During production, we occasionally encounter products that exceed the reception sensitivity standards.
Of course, we only select those that completely exceed...
I need to use PPI on my custom nRF52840 board, which selects soc nRF52840 as per copying nrf52840dk. However, this doesn't enable "HAS_NRFX", which is hard to track how that...
Hi,
I'm running the location sample on nrf9151dk from v3.0.0 of nrf-sdk. Hardware details:
I have these additional configs added to my prj.conf
This is the output...
I am working on a custom Cluster Definition Using Matter Cluster Editor 0.1.0 I have created a couple of structures on the structure tab and they are not being saved to the...
I am designing a wearable device that uses BLE and UART. During the development stage, I worked with the nRF52 Development Kit and started with the ble_app_uart example from...
Hi,
What would be the best way to alter pin's functionality from UART TX ->RX->GPOUT ->GPIN in runtime? (NCS2.5/Zephyr nRF52840)
Is it supported by Zephyr/devicetree...
Hi. I can't build the hello_dect example using cmake, the build process is failed with the following error: In file included from /home/cybermag/ncs/nrf/modules/trusted-firmware...
Hi,
In this post Hung Bui states that there can only be "maximum 4 pin events, each for one GPIO pin (so max 4 pins at a time)". This is (apperently) not true since I...
While scanning for devices with NCS 2.9.2 my device suddenly stops sending adv reports after a few hours.
It seems like this might have been fixed in a recent version...
BOARD: nrf54l15 DK
SDK: 3.1.0
Hi,
I am trying to setup my low power preipheral with a new ble address via bt_id_create.
Everthing works fine when I use the exact...
Hello! I am developing an application for the nRF5340, and I am using split cores, so the controller is on the network core and the application is on the other core. I want...
