Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hello! I'm reading the documentation that exists for the nRF5340 and struggle a bit about the Secure attribute unit (SAU) If you read the ARM documentation about TrustZone...
Hello.
I am developing Central device which support LESC.
I have some question about connect to Servers which have diferent LE security
for example case, one of...
Hello,
I am using nrf sdk 1.5.1 and trying to connect the Nrf ZigBee router(light bulb example) with Digi Xbee Coordinator but it doesn't seem to connect. I observed the...
Hello all,
I'm interacting with some nodes in a test network:
setup: 10x nrf52840 DK (PCA10056) boards loaded with the following software.
1x Coordinator ( Zigbee CLI...
Hello,
I'm using nRF SDK v1.6.0 with nRF9160 development board. I did minimum changes to Asset_Tracker_v2 application (enable debug log, set up for my aws account and to...
Migrating from nRF5 SDK to nRF Connect (Zephyr) what is the best way to define pin names using a custom board? in nRF5 SDK the header file custom_board.h usually defines the...
If I enable CONFIG_ASSERT=y this example will crash (or code using the DF APIs)
To reproduce:
- nRF Connect 1.6.1
- In direction_finding_connectionless_rx add CONFIG_ASSERT...
HI Devzon
currently my customer has some question about the power consumption difference between "LOWLATENCY" & "LOWPOWER" on NRF5340 GPIOTE
we useing PPK2 to testing...
hi support team，
customer have one problem that saadc is high rate sample at about 800hz, it runs ok, but after ble connection and send data to device from mobile device...
Hi , My application works on ncs v1.3.0, and now I need to upgrade the SDK to upgrade the application to work on ncs v1.5.1. I have completed the application development on...
Hi,
I am developing a PCB with the nrf52840 chip. The chip is implemented as described in the datasheet ( Circuit configuration no. 6 for QIAA aQFN73 ), using the files...
We are encountering a very strange situation. We have two custom PCBs (PCB1 and PCB2) both with an NRF52832. We were able to program both PCBs (multiple times) with the JLink...
Hi
I'm trying to file open and write for logging temperature data and others on nRF52840.
I successfully open, read and write on SD card or flash in nRF52840.
I also...
I am looking for technical support on Nordic Chip NRF52805 chip recommended footprint – BGA pad size.
Based on the application note on WLCSP Package guidelines from Nordic...
I'm moving from SDK 1.5.1 to 1.6.1 and when I recreate the project using the new version I get;
C:/Users/randall.philipson/kodiak_core_iot_zephyr/core_iot/prj.conf:88...
