FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
Hello,
I have a: nRF5340DK connected to Windows10 PC via USB.
I also have these that are working fine in terms of being able to communicate with the nRF5340DK over Bluetooth...
nRF SDK version is 1.5.1
upgrade modem fw to 1.3.0
Is there any way to do software reset on GPS modem? I have ran the gps example and I notice that "printk" sends everything...
I'm using the nRF5340 DK with the HRM example. My phone is HUAWEI mate 10 (Android 10).
I could scan the Zephyr Heartrate Sensor in nRF Connect App and nRF Toolbox App ...
Hi Team,
In continuation with Case ID: 269054, 269278
I am using NCS (as suggested) to avoid high current consumption happening during softdevice initialization.
I set...
Hi, I'm enthusiast of nrf5340 DK. BUT: in the samples I'm not able to find some viable openamp (other ipc seems to have the same problem) example. I am looking for a way to...
To the kind Nordic support team,
I have got a nRF52833 based Raytac module I'm using to develop before using a custom board.
I'm using Microsoft Bluetooth Virtual Sniffer...
Dear Hardware Application Engineer,
We are using nRF ASICs for our IoT products for the past two years.
In nRF52x series products, forex. nRF52840, there is a power supply...
When I do a DFU on my device (nrf52832 with Zephyr) using nrfConnect, the update is successful, but I get a message in the log stating "Length of data to send exceeds MTU...
Hi Nordic,
I am using the Raytac module with the nrf52840 inside, I have set my hardware as mode of Reg0 DC/DC enabled. Which disconnected the VDD and VDDH. Also I have...
Hello,
We need to use the RX TX on TTL level. That is possible with the nRF24L02 chip, as fa as I can understand from the datasheet. But we also need to use 8 bits, even...
Hello,
I am using nrf52840(nRF5 SDK v15.2.0). armgcc compiler, softdevice s140 hex, and application + OTA bootloader combined hex file.
in my application, I have some...
Hi,
We're developing with Zephyr OS on nrf9160 and recently added SD Card support. We build our application also for qemu_x86 for testing purposes and would like to add...
Hi!
Hope you are doing well!
I was wondering if we can use a normal characteristic to do the buttonless DFU (i.e. transmit all .hex file through that normal characteristic...
Hi, I have a few questions related to extended advertising. I am trying to receive extended advertisement sent from an nRF52832 with an ios device. The Softdevice used is...
