I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
From what I understand, the nRF52832 supports the following BLE5 features:
-2 Mbps
-CSA#2
-Advertising extensions
The chip does not support the 'Long Range' feature...
Which of the configurations will work and how?
1) Single Nordic device acting as a Nordic_UART peripheral and multiple smartphones with UART application (central) receiving...
Hello,
nRFSD5 v16.0, softdevice v.7.0.1, nRF52840
We have an application where we receive data from mobile application whenever it writes to a certain UUID. The data is...
Hi...
How to read and write to the external flash
I am using sdk 15.2 version, interfacing the development kit nRF52832 with w25q64 external flash via spi. I have read...
Hi,
I have a Thingy:91 v 1.0.0 which runs fine with the provided asset tracker firmware thingy91_nbiot_dfu_2020-04-29_bc7ade8b.hex. Cloud connect also is fine.
I managed...
Hi Didrik Rokhaug,
sdk:ncs v1.2
Routine path:D:\ncs\v1.2.0\nrf\samples\nrf9160\at_client
The routine is attached:
The test results are shown in the figure below: ...
Hi,
I want to update the firmware of my Nordic controller nrf52810( DFU Target ) using ESP-WROOM32(DFU Controller) using BLE protocol.
Please suggest how to proceed. ...
I am trying to communicate between my mobile Bluetooth and a BLE sysyem (Bluetooth low energy chip and evaluation board). The BLE chip I am using is NINA-B301 and evaulation...
I experimented with nRF52840 for 1 month. It was uploaded to the board well before, but suddenly I can't get the port.
So after finding a lot of Q&A, 1. Press button-4 ...
I've just moved over to the latest SDK version 1.3.1 (i uninstalled the previous version before installing the new one)
I installed it via the toolchain manager as usual...
Running an application that is using a 32 Mhz SPIM3 interface and it is working fine on our custom board.
As part of the interface testing, a logic analyzer was used to...
According to what I know, the nRF52840 lacks hardware to support AoA as defined in BLE 5.1. Still, the web page of the device mentions that it supports BLE 5.1. What is the...
Hello, I'm trying to send some payload via ELECTRICAL_MEASUREMENT cluster. The sending is realized in the similar way to the zigbee_light_switch example. I'm sending data...
Hi,
We have been working with an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
By measuring with the power profiler kit, we got a system...
I am developing an application that includes custom services. The application is updated by the bootloader. I looked up the post about NRF_ERROR_NO_MEM and modified sdk_config...
