Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
Hello,
I am working developing an application that sends data as notification to connected host at the data rate of 2KB/sec. The chip being used is NRF52832 with S132 soft...
Hello there; My setup: NRF52832 SDK 15.3 I'm facing some problems with FDS when i use it with BLE activated.
When i read or write on FDS using fds_record_open or fds_record_update...
I followed the steps mentioned in the Bluetooth low energy Characteristics, a beginner's tutorial, but at "if ((p_evt_write->handle == p_our_service->characteristic1_value_write_handler...
Hi, I tested "Simple_coap_client" and "simple_coap_server" on NRF52840 using Threading SDK.
I want to change the transmit power, so I used "otPlatRadioSetTransmitPower ...
52810, LIS3DH, I call nrf_drv_twi_tx got NRF_ERROR_DRV_TWI_ERR_ANACK return using either TWI/ or TWIM . Here is my code:
const nrf_drv_twi_config_t config = { .scl = TWI_MASTER_CONFIG_CLOCK_PIN_NUMBER...
Hello,
I want to verify with you if the Standby current for My Bluetooth 5.0 corresponds to the system "on" according to the Bluetooth datasheet or there is another way...
Hello, we've built up quite a bit of experience programming Nordic targets with Keil and nRFgo studio. We love your products. However, we are considering moving away from...
I'm trying to get debug output to appear in my Segger J-LINK SWO viewer (from an NR52840 SDK board with NRF5 v16) which I understand is a potentially complicated process;...
I use Peer Manager for storing bonding infomation with nRF52832 (SDK14.2) using gcc.
I understand Peer Manager uses FDS, and FDS uses flash memory from 0x7D000 to 0x80000...
Hi All,
I know this question seems to have been asked many times already but still does not seem to work for us even after checking forum answers.
Hardware: Fanstel BT832...
I have followed up this example and compiled successfully but the NFC pairing is not working at all.
I use my smartphone (Google Pixel 2) to touch the NFC antenna and nothing...
I can control GPIO P0,but can't control P1, when I load project with nrf5340_dk_nrf5340_cpuapp ns configuration.
If I load project with nrf5340_dk_nrf5340_cpuapp configuration...
Hello,
I am using a custom nRF52840 ( SDK 14.2.0, SoftDevice S140) based board to connect with an iOS(v 13.3) phone.
I am running a custom application which uses the...
At this time my project is at very beginning state, I am picking up right tools to start my project development. I have spent good amount of time to research about my issue...
