Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Trying to compile samples/net/wifi/ to test the esp8266 with Nrf52. we have our custom board. but Im' testing using Nrf52840 DK now.
I've this file
in myProject/boards...
We have a custom PCB with GPS circuit copied from the NR9160-dk board.
The default GPS example is working fine. However, we want to combine GPS tracking and LTE-M connection...
Hello,
I am using NCS 1.5.0 and modem firmware 1.2.3.
I have nRF9160 DK version 1.0.0.
I am trying to run "full_modem_update" example firmware on this.
But getting...
HI
I use NRF9160 serial_lte_modem to test NBIOT/MQTT, current SDK is V1.6.0 ,and config mqtt keepalive =1200S.
after 9160 connect net, control mqtt connect my mqtt server...
I have connected 3 Peripheral using Name Filters and 1 central.
I am able to connect and communicate with all correctly.
But I need to identify that conn_handle 0x0 ,...
Hello!
When collecting dc1.4v with SAADC, there is an error of 100uv. SAADC is configured in differential mode, with N-terminal connected to GND and p-terminal connected...
Hi,
I've read in these forums and seen the machine instructions within the C code that nrf_delay_us (which BTW is used to do nrf_delay_ms) is implemented by executing a...
Hi team,
I would like to know the default channel used for data transmission and the frequency of the channel.
Also whether the frequency is configured in the softdevice...
What is the purpose of the external capacitors on DECA and DECN? DECA calls for 1uF and DECN calls for 0.1uF. The datasheet calls these out as "Regulator Supply Decoupling...
Hello,
sorry to border you again, but I have a problem that block me for many days. I read all nordic questions on TWI (I2C) but did not found a solution... :(
I have...
Hi,
We are designing a custom Board using nRF52840 SOC.
We are operating it in Normal mode, using an internal DCDC converter
We have used configuration 5 from the...
Hi there,
I need to transmit 33995520 bytes from nrf52 peripheral device to a Windows/Android device. Currently it takes about 13 to 14 minutes to complete the data transfer...
the flash of the nrf52832-QFAB is 256KB. the softdevice S132 is used which consumes 152KB and the compiled file of the BLE_UART only consumes 98KB (after making the changes...
