I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Dear Community,
I am working on a project where the idea is to build a board that can measure the resistance over a small biosensor. The biosensor will be connected between...
nRFConnect for Desktop v3.3.0 App: Bluetooth Low Energy v2.3.2 Windows 10 x64 ( 19.04, 19.09), using Dual Monitor. Device: PCA10059 or PCA10056
I can start, connect, and...
In the "Cellular IoT development on Nordic Thingy:91" video (-> https://webinars.nordicsemi.com/cellular-iot-development-on-nordic ) an nRF Connect SDK Toolchain manager app...
SDK14+Nrf52832:
I want use one pin as a interrupt pin.
when the pin level from high to low, execute A task;
while when the pin level is from low to high, execute B task...
Hi Folks,
Windows 10, clean install of ncs v1.2.0, using nRF5340-PDK with SES 4.42a. Project blinky rebuilds and runs fine. Now I need a zephyr example of creating a simple...
Hi,
What is the suggested way to switch between 64MHz and 128MHz on the application core? Normally I want to run at 64MHz, but sometimes boost it to 128MHz. Is there additional...
Hi,i use the bootloader demo code , the file path is nRF5_SDK_16.0.0_98a08e2\examples\dfu\secure_bootloader\pca10056_s140_ble\arm5_no_packs ,a fter I compiled and passed,...
Hi,
I know this question has been asked a million times before, but most of the links are now dead, and the advice seems stale. On sdk 15 and up, how do I go about setting...
Working on a BLE application on a nRF52833 development board with FreeRTOS (external/freertos), and I noticed that the SDK uses dynamic allocation for FreeRTOS, e.g., xTaskCreate...
Hi community, I need some help with mesh programming cause i'm new to it ! First, i'll explain what i've done : I create a program on visual studio, which can communicate...
Hi,
I am starting a new iOS BTLE project for a new kind of music instrument. I started with the Thingy believing that that would be a good reference design to start from...
Hi!
Working on project based on nRF52810. Everything was fine until I began to work on part to save setting in flash memory.
I've used flash_fds example SDK 16.0 as starting...
Hi,
Currently I’m working on a device which is, on the one side connected to a smartphone via BLE and on the other side to another uC via UART.
Therefore, the UART speed...
I'm trying to get the debug version dfu secure bootloader from nRF5SDK160098a08e2 running on a nrf52832.
I'm able to compile it using cmake and a gnu c compiler. However...
