hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Dear Team,
I am try to customize the some of the parameter of HTS221 temperature and humidity sensor used in thingy52 board, However if I change any of the parameter then...
I am using the nrf connect desktop application on windows with a PCA10059, and have found the application to be buggy when receiving a flood of notifications, this works fine...
I've been logged in for about a week now, and still can't log out.
I left a posting about that almost a week ago with some "bumps" later on the "back stage" section, but...
Hi!
Can anyone tell me that isthere any app which logs data automatically into txt or csv file from nrf52???
I am getting data at nrf connect but every time i need to...
PCB : thickness 1 t(1mn), 1/2oz, 2 layer
The antenna was removed and the VNA was connected between L3 and C6.
The impedance was about 100 ohms.
The part value is shown...
We have a latest set of prototypes which use an NRF52840 on a Laird BL654 module.
On two of these protoypes the module is unresponsive. We are using a J-Link Lite module...
Hi,
I was using nRF Mesh application to get the data of uint32_t from my server model(nRF52840) but nRF Mesh android application crashes while sending the opcode to the...
I am searching for complete developement kit and SDK support which can be used to form BLE mesh Network and BLE beacon device. The idea is that BLE mesh nodes will act as...
Good afternoon, dear Sir of Madam.
Our product used the NRF21540-QDAA-R7 which has gone obsolete. What is the best substitute part?
Unfortunatelly i couldn't find substitution...
Hi I am facing a issue regarding the DFU update using the nrfConnect App.
Since we recently updated from SDK12.0 to SDK16.0 and the softdevice version has been changed in...
Hi,
I am analyzing the power consumption of mesh nodes using your Power Profile Kit. I am running the example beaconing of the Mesh SDK 3.1.0 on a board nRF52832 with the...
I have designed a nrf9160 debugging board, which uses 18 and 19 pin as the log output. Then I also configure the TX and Rx of UART0 in the overlay file, which are 18 and 19...
i tried with blinky example like thiis
#pragma long_calls
__attribute__((used, long_calls, section(".data"))) int main(void) { /* Configure board. */ bsp_board_init...
Hi,
I'm working on a code using SPI.
I've changed the SPI configuration from this thread: https://devzone.nordicsemi.com/f/nordic-q-a/65072/nrf5430-spi-sample-code ...
