This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Hello,
I am using three nrf52840 DKs to test sending gatt notify data. They are one peripheral and two central.
When they each have only one Gatt Customer Service, peripheral...
Hello,
I'm facing a problem in pc-ble-driver-py. I adjusted the uuid_count, but the code still fails at the service discovery line:
ble_adapter.service_discovery(new_conn...
I try to use st25r3911 and try to achieve low power consumption.
The code configures interrupts: gpio_pin_interrupt_configure_dt ( & irq_gpio , GPIO_INT_EDGE_TO_ACTIVE ...
Hello,
I work with the Zigbee Light Switch exemple from SDK 2.7.0
After association, the device never use the Poll data as for end_device role. But, it sends continuously...
We have created Thread Network include Leader, router and end devicewitch nRF SDK v2.5.0 on nRF 52840
We found the Thread connect will offline after 15 minute and not reconnect...
This is a higher-level question because I'm having difficulty finding concise and clear practices for this sort of thing. I don't want to go implementing something subpar...
Hi folks,
I'm making an application which needs to transmit a few kB of config data (for a configuration utility), and I was hoping to do it via UART.
To that end, I loaded...
I am working on specialized PCB's for my job, and we are trying to capture modem traces for our devices. Via JTag, I have serial access to pins P0.05 (TX) and P0.06 (RX) of...
Hi All
I m developing a project in nref9160, in GNSS part, I need to use PGPS, but can I control the checking in nrfCloud? sometimes it go to download PGPS and make GPS...
Dear Nordic Developer Zone,
I am working on MAX30003 ECG ( https://datasheets.maximintegrated.com/en/ds/MAX30003.pdf ) with Nrf52840-DK. My sensor is work on the 32.768kHz...
Hi,
I have been having quite a lot of issues around connectivity and my device, all of which at this point has stemmed from MNO blocking activity from MVNO's ( here and...
I tried adding DFU capability to the broadcast_audio_sink sample. At first i copied the whole sample code to a different directory and opened that folder in VSCode which has...
We are running into an issue of stability with our LTE connection. Our nRF9160 makes a call every 5 minutes to our backend. On start-up, the device connects and starts making...
Hi,
I am working on mesh network. i need to control 10 nodes in the mesh network with having one main node. I have taken the light switch sample as an example.
The process...
Hello,
We are trying to use nrf5340 and W25Q128JV ( https://www.winbond.com/resource-files/W25Q128JV%20RevI%2008232021%20Plus.pdf ) nor flash on our own designed card. I...
