hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
I downloaded the latest nef connect for desktop version. now I want to download and install the latest toolchain manager. when I try to open the current one I get this massage...
Dear Nordic Team,
We are currently developing a smart door lock using the nRF5340 and have started with the Matter lock sample demo code on our custom hardware.
To optimize...
hello Nordic
i am working with nrf52832, and nrf52840 with ncs v2.5.0
i am on the very adge of my ram take specially on the nrf52832 soc based devices.
we are working...
Hi,
We have a product based on the nRF5340 and have a Skyworks 66407 FEM which uses a simple 2 GPIO control scheme.
We have a shield configuration which enables the relevant...
I am running the Dev Academy Lesson 4 Exercise 2 - MQTT with TLS and getting the error:
[00:00:00.650,085] <err> nrf_modem: Modem has crashed, reason 0x4, PC: 0xecb64
...
Hi there! I have a Thingy:91 which I've registered on the NRF Cloud and verified its operation by flashing the prebuild hex files to my board. After doing this, I can see...
We are using modem firmware 1.3.5 on nRF9160.
When packet loss is high, we sometimes see connection resets (NRF_ECONNRESET) reported by the modem that don't seem to be explainable...
I'm using an STA+AP configuration as well as monitor mode with a custom nrf7002 driver, which currently is working in a basic sense. I have however ran into issues regarding...
I got this chip from Raytac mdbt50q-1mv2 on a custom evaluation board , where i can access almost all the pins ( ~30/48 ). This chip came without any programs or bootloader...
Hi,
I am looking for a freelancer in a country, that has at least LTE-M for iBasis Sim cards to work on the following project.
I am building an asset tracker product...
I keep getting the following error when building this file: Pin 15 of &gpio0 already assigned to 2 other nodes
[{ "resource": "/C:/Users/User/zephyr/boards/arm/pinnacle_100_dvk...
I am trying to use second virtual interface of NRF7002 to use with custom linux driver. I intended to use it to add support of STA+AP or STA+STA mode. However, I observing...
Hi,
I am using nrf SDK -16.0 with board nrf52840. In Ble 5 we are using LE Coded PHY with S=8.
for Ble 5, the average current consumption got doubled when compared to...
This seems like it should be simple, but I cannot seem to set a custom static BlueTooth ID on an nRF52832 under PlatformIO / Zephyr - it just keeps generating a random ID...
Hello,
We are currently developing a Zephyr-based connectivity solution using the NRF5340 alongside an NRF7001 WiFi chip. Since we also want to use Bluetooth we have implemented...
