I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hi,
I have tested the MCUboot FOTA for my sensor with the peripheral_lbs sample project, by enabling the macros:
This works, and I can bootload the sensor via...
Hi,
We wanted to implement nRF5340 with our ultrasonic microphone SPH0641LU4H-1 ( https://www.knowles.com/docs/default-source/model-downloads/sph0641lu4h-1-revb.pdf?Status...
Hi,Im new to NORDIC,
I need your guidance to select the product for my application I'm in Automotive industry, looking for ble modules which has
1.ble 5.4
2.nfc tag...
Hi,
I go my own hardware, that connects the nRF52840 Module to an ST25R3916b-aq chip with SPI bus. The I2C bus is also available by using some 0R resistors, just in case...
HI Nordic support team.
I have a question relate to RSSI in proprietary_rf application.
We test on esb_low_power_ptx.
Can i read RSSI of esb_low_power_ptx?
thanks...
Hi. I'm using NCS V2.6.1 with nrf52833, and I'm trying to merge the “zephyr\samples\bluetooth\iso_connected_benchmark” sample application with the “nrf\samples\mpsl\timeslot...
Hi Nordic support team.
I incharg project replace NRF24l01 by new design with nrf52833.
Using nRF5_SDK_17.0.2 and segger studio compiler.
I using esb_tx example, the...
Nordic DFU SDK version 2.5.0. Github issue here .
When the Android screen is off, the DFU fails right after starting. This appears to be because the scanner cannot find...
Hi, I have a project using the chip nRF52832 and sdk nRF5 14.2, I'm updating the firmware to use the nRF Connect SDK 2.2(NCS).
In my project, i use spi0 and spi2, so a can...
Hi.
I start SPI as well as I2C at the same time . then build code , the build error is occur . below is error code .
The SPI and I2C cannot be used at...
Hello,
I try to building sample code nrf_dm for nrf5340DK, but I got failed massage:
.7.0-rc2/nrf/subsys/dm/dm.c.obj -c C:/ncs/v2.7.0-rc2/nrf/subsys/dm/dm.c C:/ncs/v2...
Good Morning
Im using Zephyr, SDK2.6, toolchain 2.6. the peripheral_uart example is flashed to a 52840DK. when I connect with my phone IOS NRF_connect I get the error
...
I run the LWM2M client and send the data to the server. Nrf7002dk connects to the internet via wifi. Now I would like to update the software but I can't seem to do it. The...
Hi, I want to implement OpenThread features with another sample and I'm not sure how to go about it. Is it even a good idea to add OpenThread to another sample or is it better...
I use the serial port routine SDK17.1, nRF52833 want to burn the protocol stack, s113_nrf52_7.2.0_softdevice. But when I burn it to the chip, the address is 0x1000 and if...
