I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
I set an NOPULL type input GPIO, and I found that if I put in a voltage of about 1V,
the nrf52832 will produce a current of about 30uA,
I want to know why it can be happen...
HI
I have using nrf5340 DK for the past 7 months. Sometimes, The DK gets powered up only after 2-3 minutes after giving the power supply from the PC. Even after powerup...
I'm working on a project based on nRF52840 and nRF5 SDK16. I'm using BLE with softdevice S140 7.0.1 and USB CDC ACM for communication with a USB host. Ultimately the problem...
Hi,
I'm trying to run ble_app_blinky_pca10040_s132 on Fanstel BT832 custom board with no success. After writing/verifying the app using the SES it jumps to 'unknow function...
Hello,
I have a question:
i want to send a JSON payload using the PUT-method from CoAP. For this I am creating my JSON Payload with the following function:
The main...
I am in the conceptual stages of development for a BLE test system.
The test system requires:
Fast transceiver and connection with BLE devices, preferably capable...
I know Nordic is releasing the nrf9160 on the 12/12/2018, and from what little documentation I can find it doesn't seem to have BT or NFC hardware integrated. Are there any...
Hello, I have installed nRF Connect and the Programmer following https://infocenter.nordicsemi.com/pdf/nRF9160_DK_Getting_Started_Guide.pdf At step 3.2.2 i see "No devices...
Where can I find a drawing of the footprint for the nRF52840 WLSCP? Normally it would be near the end of the datasheet, after the mechanical drawing of the package. The datasheet...
I have an application running a serial communication through a RS485 interface. I have two sensors attached through I2C/TWi.
I have a app_timer that quwry the sensors once...
I have built on the CoAP example a POST request to the server. This works now without any problems.
I do send the received signal power within my POST. To get the power...
Hi,
I purchased a NRF9160 DK and am having problems on the first time I am trying to compile the SERIAL_LTE_MODEM application . I followed the steps according to the documentation...
Hello,
when I open any example Project from https://www.nordicsemi.com/Products/Development-software/nRF5-SDK with Keil MDK v5, I directly get the Error Message "Cannot...
Hello,
I'm a beginner of nrf5340, when I tried hci_pwr_ctrl(ncs v1.5.1) , I met some problems.I adjusted the tx power and changed prj.conf :
Then I added hci_rpmsg...
