Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Note: related to
Last week we had an issue regarding camera flash triggering reset and undefined behavior in our nRF52832. We have been able to reproduce this issue in...
Hi Everyone, I'm using nrf9160 sip, mfw_nrf9160_1.3.7 modem firmware version, slm example, sdk v2.8.0. When I include lte_auto_connect() function or manually configure the...
Hi Support Team
We want to use Windows PC to do the BLE FOTA for nRF52840 BLE device. The following DevAcademy exercise mentions that AuTerm can be used to do the FOTA on...
Hi
I found another bug in the BMA4XX driver.
When using "CONFIG_BMA4XX_TEMPERATURE=y" there is a compilation failure.
Line 621 of bma4xx.c:
Unfortunately the...
I am using Segger Embedded Studio V8.24 with nRF5 SDK 17.1.0 to build the example ble_app_bms_pca10056_s140 . This is the original Nordic example without any changes .
When...
Hi!
I have just received the nRF52840DK board and am currently perusing its schematics. Please don't be annoyed by my following question, but there are things I'm quite...
Hi,
I have tried the led strip example program and it works. My project will use 88 WS2812B RGB LEDs. For testing I used only 5 WS812B RGB LEDs. If I want to turn on red...
I have some questions regarding the power consumption for the nRF54L.
For sleep current:
1) The summary table shows 96kB RAM retention w/ GRTC is 2.0uA, but later in the...
Hello,
I've recently picked up Thingy 53 and NRF7002EB shield and wanted to play around with it, but I have a problem during project configuration.
When I add -DSHIELD...
Hi, I just tried installing nrfutil on linux with aarch64 architecture and with i try to use it i get error.
how i installed it:
after installation I ran the...
Hi, With nRF5340 DK, I am using CC registers of NRF_TIMER2 (as a free-running Timer), and DPPI, interacting with Radio. I set up a Timer Compare (functioning as a timeout...
Hi, I am having trouble setting up the partition manager in external flash with nRF54L15dk in NCS 3.0.0. I did not find any examples of this working. Interesting thing is...
1、How can I find the QEDC configuration for NRF54L15 or the QEDC demo? I found that Nordic courses do not offer these options. 2、Another issue is that I am using QSPI routines...
Hello,
If I set the connection interval to 300ms, can I call bt_nus_send multiple times (e.g., every 100ms) within that interval?
Additionally:
How can I check if...
Hi,
As the subject says, is there any way to get satellite count through at commands while using the AT firmware on NRF9151?
I'm currently using AT firmware version 2...
