pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
We're getting this strange AppError that is supposedly coming from the SD (considering the PC is correct)
App error: id: 0x00000001, pc: 0x0001505C, code: 0x00000715
I...
It looks like the DK comes with a coin cell type battery and there seems to be a tab that can be pulled off to activate. Can someone explain how to switch into battery mode...
Hi,
Which BLE dongle can we use on PC in order to communicate with nRF52810 and nRF52832 chips?
Is there a desktop version of "nRF uart app" for reading and writing...
Hi all!
I want to run OTA DFU over Thread from a RPi3. Previous tests from a PC were successful.
I installed nrftuil: sudo pip3 install nrfutil==5.2.0
I added the...
Hello.
I am wanting to send an infrared signal from my nrf52 DK (pca10040). I've found code online for sending custom IR signals using pwm and a gpio pin. The IR signals...
Hi! We're developing an app which connects to BLE devices for different purposes. We've successfully enabled MITM using windows(an example from Microsoft) , but are having...
Hey, I'm trying to install the cat tracker application. When I'm executing the npm ci command. It is prompting the following error
ubuntu@ip-172-31-25-55:~/aws/nrf-asset...
I am trying to code a cycle power service and I need to add a server characteristic configuration descriptor. This service is probably the only BT SIG service that uses that...
Hi, I am trying to get the voltage level of the battery using the AT_command AT%XVBAT which I tested using the at_client sample. I tried integrating it with my current code...
From looking at the code when a message is posted to "all-nodes" fixed group address of 0xFFFF it does not route. I was unable to find this behavior specified anywhere in...
Hi forum,
I am working on nrf52832, using sdk 15.0.0. I want to send the data(command) from esp32 to nRF52832 through Rx ,Tx . I have done connections rx,tx,gnd . I can...
Hi,
We are developing our stack with soft device using nRF52840 as the Controller and have the below queries
1. How to configure a static random BDADDR which will remain...
The error is
CMake Error at ../../../cmake/extensions.cmake:416 (add_library):
No SOURCES given to target: drivers__spi
This similar to
https://devzone.nordicsemi...
Hello everyone,
Hello everyone, I am a beginner in programming with OS based systems. I would like to get more into development with the Zephyr based NCS. For now, I want...
