Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
In my application I use NRF52840 with SDK 16.0.0 and softdevice 7.0.1. I want to add ECDH algorithm to my project using ECDH example in the SDK, but nrf_crypto_ecc_key_pair_generate...
Hi there,
I'm presuming that, when using the s140 soft device (or any of the soft devices), I cannot change the output of VDD to anything and must assume 3V.
I have tried...
PWM frequency and PWM steps resolution are related, we increase one and the other decrease and vice versa, we want high PWM frequency so we have low flickering and we want...
Hi everyone, after months of working with the nRF52840 dongle I decided to buy the nRF52840 DK. I work with the ide SEGGER EMBEDDED STUDIO. I tried to get the blinky example...
Hello,
I can smoothly run the sensor server / client model. I know that I can setup the periodic publication period with the nRF Mesh mobile app and don't have a problem...
I want to configure 32bytes sensor measurement data in advertise manufacturer specific data as follows.
But does not work, please help me.
My environment as follows. ...
Is there demo for video transmission on PCA10056 DK?
it is just video transimission demo. just loopback is ok.
we are using nRF52840. is it possible？ or other platform...
Dear Mr/Mrs,
I am learning to develop an Android BLE apk. I use the nRF Connect apk and Android-nRF-Toolbox to connect with my BLE device.
nRF Connect connect to the BLE...
I have an found a problem where I find FDS has 2 pages labeled as swap, which results in loss of one of the data pages.
my configuration is 2 data pages and 1 swap page...
Hi,
I modified the USB BLE example (nRF5_SDK_17.0.2_d674dde/examples/peripheral/usbd_ble_uart) to sends bytes using a timer timeout as "fixed bytes transactions" or "waits...
Hello,
We have a custom board designed using the ublox Anna B112 module which uses NRF52832. We are using it in open CPU mode and running our custom firmware.
The VDD...
Hi,
For example ble_app_uart, when the peripheral ble rx buffer is almost full, I want to control the central write with response, but I don't konw how to indicate the central...
Hi,
For example ble_app_uart, when the peripheral ble rx buffer is almost full, I want to control the central write with response, but I don't konw how to indicate the central...
