Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hello, I have an eval board of " nPM1100-EK -> PCA10123 0.8.0 " battery of li-po 3.7v 600mah battery termination voltage is 4.2V The above eval board works fine & the battery...
Greetings,
I'm trying to migrate the MAKEFILE configuration to SEGGER studio so that I could build and debug the project from there. So far, I'm stuck on the Linking part...
We are currently working on a Zigbee-based network coordinator using the nRF52840. I have a function, dfu_multi_image_write , that writes data to NVS in chunks. The function...
The Power Profiler app v4.2.0 release notes say:
"Updated PPK2 firmware to v1.2.0, which adds COM port for shell access"
Are there any instructions available how to use...
Hi,
My application is running NCS v2.5.3 on a nRF5340.
My project has FOTA via BLE, is running mcuboot, and is a multi-image build. I am trying to verify, from within...
Hello, I am trying to subscribe on a topic to get retained message.
I am using ncs 2.7.0
The problem is that whenever I am trying to subscribe to a certain topic, I have...
Dear all,
For a project we need to synchronize up to 5 data loggers, each of them is based on nRF52840. The sampling rate of some sensors can be of 1 kHz. I'm wondering...
Hi All,
I am lookging for a way to use the nRF7002 (or other 2.4 GHZ WifI solution) as a WiFi sniffer.
I want the solution to provide, for each WiFi packets in the previously...
my nRF52840 has MBR, SoftDevice, Application and Bootloader.
Can Bootloader call API in SD?
Will it be an issue? If I need to upgrade SD (could be a newer version),...
Hi there,
In Zephyr 3.6.99 I see a promisive function to make sure that the logging buffer is flushed at a certain moment of time: log_output_flush . It is using a pointer...
I am trying to use the following example, hci_pwr_ctrl . I have tried using the example just as it is but i keep getting errors when trying to build as can be seen in the...
I have a custom board with an I2C connected sensor ADXL345. I have to do GPI/O initialization to select the I2C. This works because I can read the ADXL with custom I2C commands...
Hi
I am using nrf52840 in my custom board. I have a gpio button which is assigned for as a factory reset button. So when i press the button the whole board needs toi be...
Hello,
we are looking to develop multiple BLE audio source which sends the mic data to the receiver and the receiver receive the audio data from multiple transmitters...
