Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
Dear Engineer
When the advertiser and the scanner enter the connect callback, a timestamp will be printed immediately. The problem now is that the advertiser and the scanner...
I am currently developing firmware on Qorvo's DWM3001C module , which integrates the Nordic nRF52833 . I am using nRF5 SDK 17.1.0 and the SoftDevice S140 .
My base project...
Hi Nordic engineer
I am evaluating a project based on nRF52840 and there is a question need to be confirm before schematic design start.
Due to limitation of power resource...
I used a mesh example (the example name is "mesh") for testing, and enabled low-power nodes using CONFIG_BT_MESH_LOW_POWER =y, and disabled the automatic start of low-power...
Hello,I tryed to install the CMSIS Wirzard in SES on the video from https://www.youtube.com/watch?v=b0MxWaAjMco But it deosn't work. I don't know why. I did read the DevZone...
Hi,
I am trying to integrate Buttonless DFU in my application. I have implemented all the steps mentioned in this tutorial.
Getting started with Nordic's Secure DFU...
Hi,
I recently started working with the nRF54L15DK and nRF Connect SDK 2.9.1. I'm trying to use I2C21 and SPI00, but I noticed that certain pins on the development kit always...
Hey guys,
I just came up with an error I can't explain with my current zephyr knowledge and I really can't workaround because the other MCU isn't programmable and needs...
Hi, With this setup in , I successfully built a CIS mode using my nRF5340 DKs , enabling stereo sound while the microphone is active .
However, I am currently experiencing...
Hello,
We use nrf54l15dk + MX25R8035F external flash to do the matter development on NCS2.9.0, and we meet some problems:
1. when the matter.ota is 1003KB, takes about...
Hi there,
We have a device that utilizes an NRF52840 chip. Several threads on DevZone - including this one and this one - warn about the dangers of applying voltage to a...
I am currentry trying to evaluate the RAYTAC-MDBT50Q-CX-40.
Raytac Corporation 勁達國際電子股份有限公司
But sample applications(helloworld, blinky) don't work.
I installed the...
Dears,
I made module with nRF52832. And I made also custom board with the module.
And then I tried to write FW(ble_app_uart_c_pca10040_s132.hex) but timeout error occurred...
Hi,
I was working on Channel Sounding for my NRF54L15 boards and suddenly the boards in "connected devices" were no longer visible. I don't know how it happened and what...
Hi,
I tried to change security level, but it's not changing.
When i set CONFIG_BT_SMP_SC_ONLY =y, it's working well with security level 4,
but i want to change mode1...
