[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello everyone,
I am currently working on implementing the flash protection feature for the 54L05 chip. My objective is to safeguard the code storage area from unintended...
I get a bunch of errors like undefined reference to `mbedtls_ssl_free', `mbedtls_ssl_get_bytes_avail',`mbedtls_ssl_config_free', 'mbedtls_ssl_read'
`mbedtls_ssl_set_bio...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
I am new to Zephyr RTOS . i have a breakout board of Max32664D from protocentral interfaced to nrf52840 development kit . i want to get started with this sensor hub max32664...
Hi Nordic team,
I’m working on a custom LoRa interface using the Thingy:91X, and I’d like to know whether the Qwiic connector pins (P0.03 – SDA, and P0.04 – SCL) can be...
based on SDK v2.9.0
1 Central, 4 Peripherals, Repeat the following:
Power off 3 Peripherals, wait a while, power on 3 Peripherals.
The following error usually occurs...
We've started development on a project using ble_app_uart as its base. We're using the nRF52832, Segger Embedded Studio (version 5.42a), and nRF5 SDK version 17.0.2. Minimizing...
Hello,*
I'm new to nRF Connect SDK environment, but I'm used to work with Zephyr.
I'm actually confused using west.yml file. I created a new application based on existing...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
Hello Nordic team,
I would like to automatically patch the merged.hex file each time I build my project. I’ve attempted to use extra_post_build in CMakeLists.txt , but my...
Hi:
PLEASE CANCEL THIS TICKET
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party...
I am trying to go through this document to see fesiability of different bootloader variation
Enabling a bootloader chain using sysbuild
using nRFConnect v3.0.1 on nRF52840...
