Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Can anybody help me please?
I'm trying to find a chip that will allow me to connect to my smartphone's internet connection over bluetooth.
I don't want to create an app...
I installed nRF connect for desktop in ubuntu 16.04. I added Programmer app . It was working fine till yesterday. But I update it from the nRF connect today. But now programmer...
Hello,
I try to use the opus codec on an 52840-DK. The Build and Flash with ARMGCC woks fine (with gcc-arm-none-eabi-8-2019-q3-update) but I'd like to use the debugger from...
While using the Zigbee OTA examples (nRF Thread and ZigBee SDK v3.1.0), I have noticed by the sniffer, that the attribute “Block Request Delay” is presented in the OTA Upgrade...
Hi! A strange problem we encountered is a different behavior of our boards before and after cutting the SB40 bridge and place a jumper on P22.
First part which works as...
Hi,
We are using NRF52840 DK in our project.I am using keil5 uvision, using SDK 15.3.0 and soft device S140.I have installed nrfx command line tool version 10_3_0 and nrfgo...
I'm using Segger Embedded Studio 3.52, nRF SDK for Thread and Zigbee v3, nRF52840-Preview-DK
I have a Zigbee Coordinator and Zigbee Router that work great at my home office...
I can success transplant saadc and fatfs to my ble project.However, when there is a SD card, the slave can write data to SD card successfully, but disconnect with the master...
Hi engineers, I got a question regarding nRF52840 (PCA10056), i want to run DTM using PCA10056 board with MT8852B tester. Unfortunately, i keep failing to get the EUT address...
Dear all,
Our application is made of
Chip nRF518122 + SDK 11.0.0 + DFU Bootloader + BLE application (gcc complied) loaded with nRF Toolbox over the air
we are putting...
Hello,
the nRF9160 product specification 1.0 states in 5.1.4.2:
"Note: The LTE modem requires using LFXO as the LFCLK source."
I checked the clock register and noticed...
Hi,
I have developed an SWD working code which read-write the Flash Memory and RAM which is working very good.
Now I have a problem in I need to write start address...
Due to time pressure, I'm starting this thread based on an existing ticket: https://devzone.nordicsemi.com/f/nordic-q-a/51423/firmware-on-custom-board-application-bootloader...
Hi team,
We have a customer who has some questions about GPS.
The questions are:
Where do we save the Ephemeris data when GPS code start? RAM or flash?
When use...
