hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi all,
I am a beginner with nRF24LE1, when I want to code some examples using GPIOs, I find that it's difficult to understand the PxCON register function. Whether I configure...
I am using the usb port to download an example project to the NRF development kit board, with Keil4. Somehow it keep telling that "No jlink device found", in Keil, the project...
I'm designing my own pcb with a IMU and nRF51422 but i confused,
What's the best choice, LDO, DC-DC or external regulator configuration if I'll use a cell coin?
Someone...
Hi,
We bought new some new nrf51822 beacon boards to get latest revision HW. Then upgraded Keil uVision to latest 5.13 and installed SDK 7.2. However I can't get anything...
I would like to use a network of nine nRF24L01+ nodes {n0, n1, ... n8} in following topology:
n0 has bi-directional links with n1, n2, n3 and n4;
n1 receives from...
Hello,
i'm using nrf51422 with gazell protocol.
Here is my interrupt on success code
void nrf_gzll_device_tx_success(uint32_t pipe, nrf_gzll_device_tx_info_t tx_info...
Hi,
I'm using two STM32F407 discovery kits with one nrf24L01+ module attached to each kit.
Here is my common init code (common for both Tx and Rx):
RF_Init(); /*...
hi:
On ios8 system, sometimes after iphone switch Bluetooth, ancs does not work,
because apple_notification_setup() is not work, but try calling apple_notification_setup...
Hi Nordic DevZone User,
i want to ask if there is a limit of devices which can be found within one scan process?
And how many connections can one master have at the...
We have two nRF51822 chips ("A" and "B") connected via GPIO pins on our board, communicating via UART using the app_uart SDK module (in APP_UART_FLOW_CONTROL_ENABLED mode...
Hi,
I found this (PCA63506) Nordic Board, which I suppose is some kind of audio interface for the Smart Remote 2. However, I am unable to find more information on this...
Q: Is qualification process simplified by some sort of NRF81522+ S110 stack BLE pre-qualification (up to GATT level, what BT SIG ask for BLE devices)?
We use NRF81522 with...
After SD initialization and turning on advertising i have to send large amount of data via SPI continuously. SPI driver code initializes SPI module after SD init and advertising...
Hi,
I have an ISP130301C chip based on the nRF51822 chip.
I'm using the jLink Segger EDU to flash the chip without any problems.
But it seems like nothing is running...
Hi,
I just took a look to nRFgo to see how it generates vendor specific UUID's. It looks if they are generated completely random including the version number. According...
