if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version: 8.0.0
SDK: 9.0.0 IC:
NRF51822 Rev 3
service: NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I tried to make CSMA/CA perform on nrf52832 but the SDK example didn't have Energy detection (ED) and CCA sample
How to configuration Energy detection (ED) and CCA ?
If...
Hello,
I am using nRF52840, SDK16 & SoftDevice140.
I am integrating pm_init()(Peer Manager) into my project and I am getting error 0xFFFFB180 from mbedtls_ecp_gen_keypair...
Hello,
We are using the nRF52 DK board and Keil uvision 5.
Using SDK 17.0.0 we can successfully load and build the `examples`. If we choose `examples/peripherals` we can...
Hello, everyone.
I would like to use LSM9DS1, a 9-axis IMU sensor. To test this, an IMU sensor module 'SparkFun 9DoF IMU Breakout - LSM9DS1' was purchased.
This module...
I am working with Zephyr version 2.4 on nRF52840-Dongle for adding ability to scan CODED PHY devices. My host is Raspberry Pi3 with kernel version 5.4.51 v7+, HCI_USB sample...
Hello,
I am trying to run USBD_MSC example using PCA10056 board from SDK15.
It works fine, when creating new file on each button press.
I modified code to create and...
Hello everyone ,
I have question about the difference between periodic message publishing via the module's configuration and publish message by a standard timer.
I notice...
nRF52833 DK i have seen from Images of board that an external antenna will be required(there is a Antenna connector on board). I am wondering if it has built-in antenna or...
Hello,
I am on nrf-sdk v1.3.0 and mwf v1.2.0.
We are updating our product to the above mentioned nrf-sfk version and have noticed that MQTT connection gets stuck after...
Hi,
I enabled flash log backend with NRF_LOG_BACKEND_FLASH_ENABLED set to 1, and NRF_LOG_BACKEND_FLASH_START_PAGE to custom address to keep it as the starting address for...
Hi,
We have successfully created a PCB layout with a PCB antenna following the reference schematic provided by the nrf8001 datasheet. We tested and it is working fine. However...
Hi,
I am trying to interface External Flash (IS25LP064A ) using SPI example in SDK v16. I am able to read the Manufacturer_ID and the device ID from the external flash....
Hi,
Is it possible to somehow read END event register via CPU (not with ppi usage)? If yes, how? I have tried to read value on address from pointer returned from function...
Hi, I am facing an issue my product contains Ble dfu update, I tested my code without enabling DFU and it runs fine ... but after enabling dfu and creating package... I update...
Hello, everyone!
I use SDK v17 and test various functions using App_Timer. The timer function that I want is to turn the LED on for 5 seconds and then turn off after 5...